spinnerbait- this is the original fishing bait, which was invented about 100 years ago in the USA. She later received Spread throughout the world, because attracts very different and allows you to catch in difficult conditions. Highly good results can achieve with spinnerbaits on a pike hunt.

Name spinnerbait derived from two English words: "spinner" - spinner and "bait" - bait. It consists of five main parts:

• a piece of wire bent in the form of a corner - rockers;
• one or more petals, which are located at the top of the bait;
• hook, located in the lower part of the rocker arm;
• lead head like a jig;
• silicone fringe, which closes the hook - skirts.

Reference. Many anglers believe that a spinning lure should look like a potential prey to a pike. First of all, this applies to beginners. The unusual design of the spinnerbait scares them off, as this lure is unlike any living creature. However, in reality, it turns out to be very catchy.

In pike hunting, vision is not the most important role. When posting spinnerbait creates vibrations and noise under water, petals revolve, a skirt swaying, becoming either wider or narrower - as a result, this the bait attracts pike well. She turns out strong irritant and provokes a predator for a bite.

In use the skirt is gradually falling into disrepair- when biting, the pike cuts it with sharp teeth and gradually plucks it out. However, this element of the spinnerbait is m can be replaced with a vibrotail or twister- on the lure catchability such a permutation almost no effect.

Spinnerbaits for pike: wiring technique. Video

Catching pike on a spinnerbait in the video below:

Advantages

Spinnerbaits suitable for fishing in the most difficult conditions- this is their main advantage. Such baits rohat through thickets of grass and snags are the points where the probability bites pike maximum. This is explained by constructive spinnerbait features:

• yoke wire securely closes the sting single hook from collisions with objects, for which it can cling;
• thanks to located at the bottom of the cargo the bait is located vertically during posting, therefore walks easily on the grass;
• rotating petals spread the blades of grass and facilitate the course of the bait, due to which the likelihood of hooking is further reduced.

Another plus spinnerbaits that they often are more catchy than other baits. There are situations that pike greedily attacks from time to time, in while the wiring of rotating and oscillating baubles, wobblers, silicone fish e brings bites. This is another argument in favor of have in the collection at least a couple of spinnerbaits.

How to make a do-it-yourself pike spinnerbait

Spinnerbaits - expensive baits, and models, which are suitable for pike fishing, this applies in the first place, as they differ large sizes and must have increased strength.

Therefore, many anglers buy to the collection no more than 2-3 pieces. However spinnerbaits for pike you can make your own.

For this need:

• steel wire about 1 mm thick;
• brass sheet or stainless steel with a thickness of about 0.3 mm for the manufacture of a petal;
• hook with a long forearm;
• two winding rings and a swivel;
• rubber bands for money, from which you can make a skirt, or silicone lure suitable size.

It is also necessary to have plaster mold for pouring the lead head, a mold for making a petal, which can be made, gulf molten lead metal jar and placing it in a spoon, and punches made of hard wood.

First thing need to bend wire yoke. In his central part must be located loop-ring through which it will be attached to the fishing line.

Thereafter attach a hook to the bottom of the metal corner, bite off the excess end of the wire and pour head of molten lead.

Important! The lead sinker should cover the junction of the rocker and the hook. It will give the necessary structural strength, which is necessary, since this point will have a large load when playing the fish.

Then make a petal. For this cut the workpiece from sheet metal, drill a hole in it and give her desired bend using a mold, punch and hammer.

Thereafter fasten the petal at the top of the rocker. For this twist the end of the wire into a loop, and then mount the element through two winding rings and a swivel.

Remains only fasten the skirt, tying it with a thread and fixing it with waterproof glue- and the bait is ready to use. Another variant - attach a vibrotail or twister to the hook.

Making do-it-yourself spinnerbaits for pike is not an easy task. because they have a complex configuration. But at having some experience can make bait, which are nothing they will be inferior to factory models sold in stores.

At making spinnerbaits experiment with shape and size rocker, shape, size and number of petals, as well as the size of the hook to find catchy configurations.

fishing technique

At pike fishing on a spinnerbait uses two types of wiring:

• uniform;
• undulating.

First suitable for catching active fish. When pike is hungry and waiting for prey uniform wiring is enough to provoke a bite. If you want to achieve best results, lead the spinnerbait in bottom layer so that he periodically hit the bottom while losing work. The even hauling also allows you to quickly explore vast areas to find fish.

But often more effective turns out wavy wiring. She assumes uneven winding of the line- coil handle needed rotate faster or slower. In this case the bait is moving in water by wavy trajectory- every now and again is accelerating,climbing up, and then slows down its pace,going down to the bottom. Skirt while clearly swaying, becoming then wider, already- thereby spinnerbait becomes more attractive to pike.

Another variant - carry out undulating by using rods. For this it is necessary in rotate the reel handle evenly, wherein smoothly shaking the spinning up and down.

spinnerbait- it's original and catchy lure for pike. In spite of bizarre view, she is well provokes a predator for a bite. Therefore, everyone who has not had time to try spinnerbaits in action, definitely worth it pay attention to them.

Useful video

Do-it-yourself spinnerbait in the video below:

Lovers and professionals of this catchy fishing always strive to come up with something that will help you as much as possible more fish. Based on this, such a bait as a spinnerbait was invented.

At first glance, the design looks complex, as well as voluminous, but it can be easily made at home. It will be discussed in more detail below.

What is a spinnerbait?

Spinnerbait is a kind of bait that is actively used by spinners when catching predatory fish. In general, this type of bait creates the illusion of movement of a flock of fry. A large predatory fish, seeing all this action, reacts to a flock, tries to attack it, and eventually gets hooked.

Types of spinnerbaits

These baits differ in appearance. These are the differences:

• At different types lures can be differently disguised hook.
• Also, the difference may be that a different number of petals is used.

Now we can define the following types:

1. In addition to classic lures with one petal, there are varieties with two petals. They are located one after the other. It gives the impression of an impromptu school of fish.
2. Catchers. Here the silicone "skirt" is replaced by any other silicone nozzle.
3. Buzz baits. In this version of the bait, a mini propeller is used instead of petals. When immersed under water, it seems to be “screwed” into the water column. The propeller makes a characteristic sound, which attracts fish. This option is the least popular. This is due to the fact that such equipment is used only for pike fishing.

DIY manufacturing

It is quite possible to make a bait with your own hands, the main thing is to stock up all the necessary elements and materials. But, before you start making a spinnerbait, you should understand how this bait works. The design will be discussed below.

The design of a homemade spinnerbait

Homemade spinning equipment has a metal axis made of wire, which is bent in the middle, forming one turn of the spiral. Such an axis is similar to a tick.

How to catch more fish?

For 13 years of active fishing, I have found many ways to improve the bite. And here are the most effective ones:

1. Cool activator. Attracts fish in cold and warm water with the help of pheromones included in the composition and stimulates their appetite. It's a pity that Rosprirodnadzor wants to ban its sale.
2. More sensitive gear. Read the relevant manuals for the particular type of tackle on the pages of my website.
3. Lures based pheromones.

You can get the rest of the secrets of successful fishing for free by reading my other materials on the site.

• One of the ends is supplied with a tin petal or petals.
• A sinker and a hook are attached to the other end. They are masked by a "skirt" of silicone strips.

Here is a general description of spinning equipment.

What materials will be needed?

For the manufacture of such a bait, certain materials and elements are needed.

Here they are:

1. Piece of wire. It is desirable that it be stainless steel. The thickness is chosen not too small, and not too large, 1 mm will be enough. With such a thickness, the wire bends well in different directions, but at the same time keeps its shape.
2. Hook with medium length shank.
3. Tin sheets.
4. Rubber bands for money, residual layers of rubber or silicone material, if any.
5. Liquid lead or ready-made sinker.
6. Various beads to "decorate" the spinnerbait.

Of the tools you need:

• pliers;
• Casting mold made of lead weights;
• Metal scissors.

Manufacturing process

When everything you need is prepared, you can proceed directly to the manufacturing process.

It includes several sequential steps:

1. Initially, you need to take a piece of wire no more than 6.5 cm and bend it in half so that you get a “tick”. The bend should divide the wire almost in half.
2. A pre-cut petal is attached to one end. It can be made of stainless steel, as long as the metal is no thicker than 0.3 mm. You can also attach a few petals. In this case, the second, third, and subsequent petals are fastened with a swivel and clockwork rings. This is necessary so that the petals do not get confused with each other.
3. A hook is attached to the other end of the wire.
4. The junction of the hook and wire is placed in the form for pouring the sinker. Now you can pour liquid lead. Let the product cool down.
5. Now the matter remains small - it is necessary to disguise the spinnerbait, or rather the hook. This is where rubber bands are needed. They are cut in one place, then the resulting elements are assembled together with glue around the sinker. If the "skirt" strips are cut from a piece of silicone material, they can be made longer. This will allow you to tie the strips into a bun, and then secure over the hook.
6. Additionally, the spinnerbait can be equipped with beads for better "playfulness".

Some tips to help improve the appearance of the bait, making it even more attractive:

• The petals can be left as they are, or they can be covered with paint or the usual simple varnish. Bright colors will be more visible in the water column.
• When making a “skirt” for a hook, you should not do everything in one color, you can even choose stripes at random. A motley "skirt" will only add a sense of more movement to the lure.

Spinnerbait upgrade

On any fishing trip, some incidents can occur. For example, the hook breaks, the fishing line is confused. But what if the spinnerbait is damaged, namely, the “skirt” of the hook is torn off? Yes, this happens when a predatory fish grabs only this rubber “cloak”, and the hook bypasses.

The following baits will help out here:

• vibrotails;
• twisters;
• other options for "ready-made fish" made of silicone.

They are taken completely or some part of them, most often the tail, and put on the hook. Well, here it is completely closed, which means it is hidden from the eyes of the fish. Now you can continue fishing.

Spinnerbait fishing technique

Since the spinnerbait is an active bait, it should be carried out quickly in order to catch it if necessary. If there are no thickets on the reservoir, then the spinning is immediately thrown into the water, quick game bait.

If, somewhere, there are overgrowths of reeds, water lilies are located on the water, then you should not rush with quick wiring. It is important to lure a pike or any other fish out of an ambush with a variety of rigging.

Feedback from fishermen on making and fishing

My acquaintance with this bait happened relatively recently, but I have already managed to evaluate its effect on fish. I concluded that the spinnerbait either gives a 100% result, or it does not exist at all. It's kind of extreme, but for some reason it doesn't scare me.

A big plus of this equipment: the hook does not cling to snags and does not get confused with thickets. All this thanks to its protective "skirt", which, as it were, repels grass and branches from the hook. Thus, I can say that I still like the equipment more than not, so I will continue to practice using it.

An interesting type of equipment, different from others. In my opinion, such a bait creates the illusion of a flock of fish, which is why a large predator pecks. I have noticed such a trend that in my pond, where I often visit, only large carp. I'm glad that it's the big ones that get hooked, because I can't stand every little thing.

One spring I went on another fishing trip. I always fish exclusively on spinning. I throw a wide variety of baits, they interest the fish, but the bite is unstable. Decided to try the spinnerbait. To my surprise, an active stable bite began. I got the feeling that the fish stood in line and one by one clung to the hook. The float did not have time to reach the surface of the water, so there was an active bite.

Stanislav

The equipment is liked by the fact that if the first bite occurred on it, then there will definitely be a second, third, and so on. The bait sets the tone for fishing, and most often the day is very catchy. This cannot but rejoice! It is worth saying that after active fishing, the equipment may become unusable or pretty shabby.

Large fish randomly grabs the “fish”, while it can bite off the “skirt” or petals. Every time after a fruitful spearfishing, I patch, tint, forge fishing accessories. Then they become like new, and, therefore, I use them again.

Making baits is my favorite pastime. I have been fishing since I was young, and, accordingly, I constantly make some interesting types of rigs. The last thing I did was spinnerbait. I made the simplest version with one petal. Already tested recently on a local reservoir. A couple of good pikes were hooked. Then a trifle began to be caught, but that's okay, any fish is good.

Such bait as spinnerbait, used in America mainly for bass fishing, but it turned out that this exotic and unknown lure is also suitable for catching perch, pike, etc. That is, the spinnerbait is fully suitable for our fish and for our conditions.

In contact with
Facebook
Twitter
Google Plus
My world

This spinning lure goes well in overgrown areas of reservoirs, it is carried out both in snags and in rare grass. It is possible to describe all the advantages of this bait for a very long time, but we will focus more on how to make this miracle bait ourselves.

But the spinnerbait was noticed two flaws, and very important ones, this is a large windage, that is, it does not fly very well when it is thrown, and because of the pike's teeth, the “skirt” of this bait deteriorates very quickly.

If you want to buy a spinnerbait, then it is better to refuse this idea, as you will be lost not only in the types, but also in various prices. Why pay money at all if you can make such a bait yourself.

All you need is the materials at hand and various little things that are in the fishing boxes. And you will spend no more than half an hour on this.

If you still decide to make a spinnerbait with your own hands, then first you need to decide what you need. From the material you will need:

• steel wire (0.6-0.8 mm);
• two pieces of cambric;
• rubber bands for bills (a few pieces, but this is not necessary);
• silicone bait, which is equipped with a jig head;
• carabiner with clasp;
• spinner petal.

Regarding the tool, you need to have:

• pliers and round nose pliers;
• side cutters;
• scissors;
• diamond file.

We begin to make our bait with the fact that the elastic bands for bills need to be cut on one side, mark the middle and fix it on the jig head back to back (you can just wind it with a fishing line). Take the pliers and use them to form a wire rocker.

Now we put on a cambric on each side of the rocker. Its inner diameter should be such that it can pass the wire, which is folded in half, into itself.

The best spinning baits, what are they? Read our article and you will find the answer to this question.

And here it is told about the choice of spinning and fishing line for it.

Then, again, with pliers (or you can take round-nose pliers), we form detachable rings at the ends of the rocker arm. Do this so that the tip of the wire does not curl around the side of the rocker, but is pressed parallel to it on each side. In the end, you should have upper arm shorter than the bottom.

Now we put on a carabiner and a jig head. After that, you need to move the tubes all the way to the rings and fix the free mustache of the split rings. If necessary, touch up the hook point with a diamond file.

Bait weight directly depends on the weight of the jig head that is used. Thus, such a bait is universal, since the head can be changed whenever you want.

And that's it! Your bait, spinnerbait, is completely ready.

Now you are convinced that many things can be done with your own hands and it is not so difficult. This includes the spinnerbait. All you need is the material at hand and half an hour of your time. With the help of such a lure as a spinnerbait, you can catch not only perch or pike, now you can also overcome zander.

Spinnerbait is not at all scary thickets of water lily leaves, as well as rare reeds. This bait does not cling to any underwater obstacles, only sometimes the rocker itself can cling. For perch fishing to be successful, you need to make a homemade spinnerbait, but smaller, for this, use a very thin steel wire. Do not be afraid that your pond is overgrown with grass, try fishing with a spinnerbait and you will appreciate this bait.

And it's not a secret for anyone that they work no worse, if not much better than purchased ones. What is a spinnerbait? This is a double rig designed for pike and perch fishing. It looks like this: there is a spinner on top, and silicone with a hook (jig head) on the bottom. At what these elements of tackle are divided among themselves. As a rule, they come in the form of houses, corners, L-shaped forms or in the form of a tick (bird).

How spinnerbait works

This snap works almost the same as any other, but still it has its own trick. The Americans came up with this tackle for fishing in places where there are a lot of snags and grassy areas of the reservoir. This is facilitated by its shape of the structure.

The principle of operation of the spinnerbait:

• It consists of one or more spinners, which create an excellent imitation of a flock of small fish. Spinners attract a predator due to their brilliance and movement. This method of fishing will be just a godsend in ponds with muddy water.
• Another type of bait is a jig head with silicone fibers. Spinningists also use twisters and vibrotails. When a predator approaches the bait, the first thing he pays attention to is the jig head with silicone. And it is located just where the hook is hidden.
• Due to the unusual shape, Bottom part tackle rests on a snag or grass and bypasses it without clinging to obstacles.

The use of a spinnerbait allows anglers to improve their fishing results several times over. And the main merit here is that it consists of two different types of gear.

And made by hand, such a device will not only save financial resources, but also give a lot of pleasure, both from the manufacturing process and from fishing with its participation.

What tools and materials will be needed for manufacturing?

In order to assemble a spinnerbait with your own hands, it will not take much time. Tools and materials for assembling tackle can be assembled from improvised means. But it is better to use those that are listed.

Types of tools that will be needed for assembly:

• round nose pliers;
• wire cutters;
• pliers;

Materials for making a spinnerbait:

• stainless wire with a diameter of 1 to 3 mm;
• beads - 6 pcs.;
• spinners from 1 to 3 pcs. (at the discretion of the angler);
• carabiner -3 pcs.;
• jig head - 1 pc.;
• silicone threads or any silicone bait - 1 pc.

After going fishing winter period, I just want to catch at least a perch. Armed with a variety of baits, you begin to look for perch flocks and find out what exactly the striped robbers will like.

It was in this situation that I was able to discover the fact that perch respond well to ultralight spinnerbaits and attack them with pleasure.

This bait can be made independently, with your own hands, at no special cost and with pleasure to spend the evening making small spinnerbaits. The result is individual, varied and pretty, which will certainly justify itself when catching perch and perhaps even pike.

To make a fishing homemade “ultralight pin spinnerbait” you will need:

• pins -2 pcs;
• winding ring;
• triple hook;
• clasp with swivel - 2 pcs;
• a petal from a spinner;
• tail part from vibrotail.

Process self-manufacturing spinnerbaits for ultralight:

1. Getting to work, first we disassemble the pins by removing the hook parts and using narrow pliers we make ears, which we will later fix with solder.

2. We attach a swivel with a clasp to the left ear and thread a petal from any spinner onto the clasp. You can also make a petal yourself from a steel plate.

3. With the help of a soldering iron and solder, we fix the ear so that there is no unexpected loss of the petal. However, the pin wire is very strong and the application of solder can be delayed.

4. We also solder the second eyelet and attach the triple hook with the help of a winding ring.

5. It turns out an almost finished spinnerbait, which can be modified with multi-colored tinsel or, as I did, fasten the tail of the vibrotail, twister onto the tee.

6. We carry out the same manipulations with the second pin, only we use a single hook, which we attach to the pin with lead.

We cut out a triangular recess in a piece of wood, fix a pin and a hook, melt the lead on the fire and fill it.

The resulting weight is covered with nail polish and dried. Lures are very interesting.

In the first case, the spinnerbait weighs 5 g, in the second case it is better to stick to the same weight, but I got 8 g.

Each angler can independently make the same baits with his own hands for ultralight fishing, or use his imagination to come up with his own interesting options.

Belikov A.A. ,Russia, Volgograd - Specially for the site