Myostimulator is a unique and modern device that allows you to completely restore the functioning of nerve endings, affecting muscle tissues. First of all, the "Impulse" myostimulator is intended for the elimination of excess weight and muscle building. Already many people use it and note its instant effect. The device, developed by leading American research centers, and has all the quality certificates. By and large, today it is quite difficult to find identical muscle stimulants.
Doctors and many professional researchers have already proven by practical tests that the muscle stimulator really helps the body. Recently, the device has received the widest distribution. The impact on the nerve endings by means of microimpulses allows you to even give relief to the muscles.
What is a myostimulator
It is no secret to anyone that all the actions of our body are under the unified control of the most complex mechanism - the brain, which, receiving nerve impulses, responds with lightning speed to the supplied irritations. That is, the nature of the flow of such a reaction is similar to the flow of electricity. The point, electronic myostimulator "Impulse" works on the same principle. Which, recently appeared on the shelves of online stores. And every day it is gaining more and more popularity.
Using the "Impulse" muscle stimulator, you can easily reduce excess weight, improve blood circulation by affecting the muscles and causing them to contract. It helps relieve muscle pain, tension and fatigue, significantly improves the condition in case of neuralgic diseases, and restores the body after heavy loads. You can use the device both during rest and during active movements, it is firmly attached to the skin with the help of silicone electrodes.
With a properly designed design, you can achieve a positive result. Most importantly, read the instructions for use. The manufacturer recommends that before attaching the myostimulator to the body, wipe the skin with warm water and then with a dry cloth. Thus, it will be much better to hold on and act more effectively. The tighter the contact with the skin, the better the result.
How does the "Impulse" myostimulator work?
The impulses supplied by the muscle stimulator activate the muscle fibers and set them in motion, due to such actions, fat cells are burned and cellulite is leveled. Silicone electrodes are applied to the skin in the right places, through them an electric current flows to the nerve endings, which give a signal to contract. muscle fibers. As a result, the muscles begin to work and a gradual tightening of the skin occurs. Therefore, using the Impulse electronic myostimulator, the result will not be immediately noticeable, but after two or three weeks of work on yourself, you will be able to feel noticeable changes. Additional physical education will greatly accelerate the expected effect.
There is a big plus in the operation of the device when compared with conventional training. What would you physical exercises if they didn’t, they won’t be able to use all the muscle fibers of at least a certain zone, that is, by pumping the press, the abdominal muscles work for us, but not all. Using a muscle stimulator, absolutely all muscle fibers of the desired zone come into play. Under the influence of the emitted electric current, all muscles are involved, stimulated and come into action.
The downside is that although the myostimulator makes the muscles work, the muscle tissues and ligaments do not stretch and the joints remain motionless, so physical activity is necessary. But still, in spite of everything, the “Impulse” myostimulator leaves quite positive reviews.
What effect does the "Impulse" myostimulator have on the body?
40 minutes a day with a muscle stimulator will replace an hour run or two hours in the gym, allowing you to train all the muscles. The device successfully copes with muscle pain and relieves tension, allows the body to relax after exertion and with neuralgia. After reading the instructions for the Impulse muscle stimulator, it becomes clear that it has 3 operating modes (tapping, modulation, massage) and 2 programs that will easily allow you to set it up yourself.
With the help of the device it is really possible to achieve, in a short time, a beautiful and elastic press, which will remain an adornment of your stomach for a long time, or beautiful biceps, from which your friends will simply be delighted. The device can be used both during rest and during active actions. Based on the presented practical data, the effectiveness of the device is fully confirmed and guarantees a positive effect. A pleasant price-quality ratio will allow you to purchase a muscle stimulator for personal use.
It is worth sitting comfortably on the couch, turning on your favorite program and attaching the muscle stimulator to a certain place on the body, and it will instantly begin to fight extra pounds and strengthen the right muscles. When using a pacemaker, it is best not to engage in any active activities. Thus, you can protect yourself from discomfort. The action of the device is aimed at restoring the activity of your tissues and muscles. In fact, you can achieve a positive result in the shortest possible time.
How to use the simulator correctly
It is convenient to train absolutely all muscle groups with the Impulse muscle stimulator, even those that are difficult to use during normal training. It is enough to install it with silicone electrodes on the part of the body that requires stimulation and set it to the desired mode of operation by selecting the program, it immediately begins to act.
The compact size of the bradex "Impulse" muscle stimulator allows it to easily fit in your pocket and use it at any time convenient for you. The device runs on batteries, so when moving around the apartment or walking in the park, no wires will interfere with you. It has a pair of electrodes that simultaneously act on different muscle groups, which saves time. With the help of several setting modes and two programs, you can easily and independently adjust it to the desired level of exposure.
Using the actions of the electronic point “Impulse” myostimulator, you will save the time that you would spend on gym. The device helps to tighten any muscle group and remove overweight. With the help of two silicone suction cups-electrodes, the “Impulse” myostimulator is attached to the desired part of the body and sets in motion, stimulating even those muscle groups that seem difficult to reach during normal training.
Effectively relieves muscle pain, fatigue and tension in the shoulder area, normalizes the condition of neuralgic pain, helps the body recover faster after exertion.
How does a muscle stimulator work?
Due to the impulse current, the muscle fibers are activated.
To do this, silicone electrodes are applied to the skin in certain places (stomach, chest, back, hips, arms and legs). An electrical impulse is applied to the electrodes of the myostimulator, which is transmitted through the skin to the nerve endings. At the "signal" of nerve cells, muscle fibers begin to contract.
As a result of this effect, the skin is tightened, and the muscles come into tone. That's why visible result can be obtained after 1-2 weeks of using the myostimulator.
Can a pacemaker replace "live" workouts?
Myostimulation has one plus, unattainable with conventional training. Whatever variety of exercises are used, they do not involve ALL muscle fibers, because our body is very economical. When the electric current is applied to the myostimulator, all the muscles to which the impulses are applied are included in the work, i.e. all muscles in the stimulated area.
However, during myostimulation, muscles and ligaments do not stretch, joints do not work. Therefore, training with a myostimulator does not exclude the usual physical activity.
What muscle groups can be trained with the Impulse muscle stimulator?
With the help of a muscle stimulator, you can train almost all muscle groups:
press
thigh muscles (including inner surface hips, which are very difficult to use during “live” training)
calf muscles
biceps and triceps
gluteal muscles
What are the advantages of the device?
Our simulator has a lot of advantages:
small and compact size. The pacemaker fits easily in your pocket. This will make it easy to combine classes with household chores, a walk and even work.
The device is powered by two AA batteries. This makes our pacemaker very portable. You can always take it with you on a trip, move freely around the apartment without worrying about wires and the availability of a power source.
2 electrodes. stimulate various muscle groups and significantly save time.
manual mode and automatic programs. A rich selection of settings will make the procedures truly individual. You can choose one of the already developed programs, or you can set everything up yourself.
The muscle stimulator offers several modes of exposure ( "tapping", "modulation", "massaging") and two preset programs.
Equipment:
- myostimulator,
- 2 pairs of silicone pads
- instruction.
- 3 active exposure modes
- 2 preset exposure programs
- Pulse frequency: 90 - 200Hz
- Material: PVC, metal, silicone.
- Powered by 2 AAA batteries (1.5 V each)
- Item weight: 200g
International trade mark "BRADEX"
Israel; Reg. No. 204012 Russia: Reg. №444287
Country of manufacture China
Warranty 1 year
1. GENERAL INSTRUCTIONS
Dear buyer! You have purchased a modern charger that allows you to charge motorcycle and recharge car lead batteries, which, when the car is used less than once a month, compensates for the self-discharge of the battery and, as a result, protects its plates from sulfation.
The thyristor circuit for stabilizing the charging current used in the device (which is reflected in the trade name of the device: ZS - charger with current stabilization), electronic protection against short circuits and from incorrect connection of the battery to the device, as well as the presence of an indication that the device is connected to the network and indication of leakage charging current, will greatly simplify the process of charging batteries for you.
When buying a device, require checking its performance before clause 6.1. this manual.
Check for warranty cards.
Make sure that the warranty cards are stamped by the store, legible signature or stamp of the seller and the date of sale.
Remember that if the warranty cards are lost, you lose the right to warranty repairs! Warranty repair coupons are cut out by employees of the service organization only after the device has actually been repaired.
Check the completeness of the device and the safety of the seals.
You can turn on the device only in the AC mains, voltage 220 V and frequency 50 Hz. Please read this manual carefully before connecting the device to the network.
2. SCOPE OF DELIVERY
2.1. Charger "Impulse ZS-01" - 1 pc.
2.2. Operation manual - 1 pc.
2.3. Fusible insert VPT 6-5 OYu0.481021TU - 2 pcs.
2.4. Individual packing - 1 pc.
Note: Fusible inserts packed in a bag are located in the cord management compartment,
8. MAIN TECHNICAL CHARACTERISTICS
3.2. Rated frequency, Hz - 50
3.3. Rated voltage of the battery being charged, V 6; 12
3.4. Rated charging current, A 1.6
3.5. Power consumption, W, not more than 55
3.6. Efficiency, %, not less than 45
3.7. Weight, kg, no more than 2
3.8. The total mass of precious
gold 0.021 metals in the product, g silver 0.014
Note: It is possible to charge batteries with a current equal to half the nominal current (0.8A).
4. SAFETY INSTRUCTIONS
With an open or deformed body;
In case of contact with the body, power cord or connecting wires of fuels and lubricants and acids;
Outdoors in conditions of high humidity (rain, snow, fog).
4.2. When the device is turned on, it is prohibited:
Disassemble and repair the device;
Replace the fuse;
Connect (disconnect) the battery;
Leave the switched on device unattended for a long time;
Locate the device near flammable substances.
5. SUMMARY
Charger "Impulse 3C-01" complies with the specifications 11M0.081.412 TU and is designed to charge batteries with a nominal capacity of up to 22 A and recharge batteries of a larger capacity with a charging current of 1.6 and 0.8 A.
The device is made in the form of a desktop device. Inside the device there is a transformer, a printed circuit board with radio elements and radiators with thyristors. The location of the external elements of the device is shown in fig. 1, and the electrical diagram of the device and the wiring diagram of the printed circuit board are attached.
6. HOW TO WORK WITH THE DEVICE
6.1. Checking the performance of the device when selling.
8.1.1. Connect the terminals "+" and "-" of the device to each other.
6.1.2. Connect the device to the network by inserting the mains plug into the socket. At the same time, the NETWORK indicator should light up.
6.1.3. Touch the closed clamps to the CONTROL terminal located on the rear panel of the device. At the same time, the CHARGE indicator should light up.
6.2. Operating procedure when charging the battery:
6.2.1. Strictly observing the polarity (the “+” clamp of the device to the “+” terminal of the battery and the “-” clamp to the “-” terminal), connect the battery to the device.
6.2.2. Set the charging current button located on the front panel of the device to the position corresponding to the capacity of the battery being charged and the recommended charging current for it.
Note: When the button is released, the rated charging current is 1.6 A. This current is recommended to charge batteries with a capacity of 12 Ah to 22 Ah and recharge larger batteries. The pressed button corresponds to a charging current equal to half the nominal (0.8 A). This current is recommended for charging batteries with a capacity of 4.5 Ah to 12 Ah.
6.2.3. Connect the device to the network by plugging the power cord into a power outlet.
6.2.4. If at the same time the NETWORK and CHARGE indicators begin to glow, then the charge can be considered to be flowing normally.
6.2.5. If there is no charging current (the CHARGE indicator does not light up), check the correct connection of the battery or improve the contact between the device clamps and the battery terminals.
6.2.6. The charge should be carried out in accordance with the operating instructions for the battery until abundant gas evolution (“boiling”) occurs in all battery banks, and the voltage and density of the electrolyte are constant for 2 hours in a row.
6.2:7. Then disconnect the charger from the mains by unplugging the power cord from the socket and disconnect the battery.
6.2.8. Check electrolyte density. At the end of the charge, it should be equal to (1.28* =*=0.01) g/cmg* at a temperature of 15 °C. If the electrolyte temperature differs from 15 ° C, then a correction must be introduced to the hydrometer readings. The correction value is given in Table 1.
If the density of the electrolyte differs from the norm, it is necessary to bring it up to the norm by adding distilled water, in the case when the density is higher, or adding an electrolyte with a density of 1.40 g / cm3, when it is below the norm. Before adding water or electrolyte, part of the electrolyte from the battery must be removed with a rubber bulb. Bringing the density of the electrolyte to normal must be done at the end of the charge, when it reaches constancy and when, due to "boiling", rapid and complete mixing of the electrolyte is ensured.
6.2.9. After charging and finishing, the battery can be considered serviceable.
7. MAINTENANCE
Charger "Impulse 3001" is equipped with protection against short circuits, overloads and reverse polarity when connecting the battery to the device, which greatly increases its reliability.
Compliance with the rules of operation of the device will give you the opportunity to operate it for a long time.
The list of the simplest faults is given in Table 2.
The list of the simplest malfunctions of the charger "Impulse ZS-01" - and ways to eliminate them
8. STORAGE RULES
8.1. The device must be stored in the manufacturer's packaging in enclosed spaces at an air temperature of minus 10 °C to plus 40 °C and a relative humidity of not more than 80%.
8.2. The storage room must be free of dust, fumes, acids and alkalis, as well as gases that cause metal corrosion and damage to the coatings of the device.
9. WARRANTY
Charger "Impulse 3001" corresponds to the approved sample.
The manufacturer guarantees that the product meets the requirements of the technical specifications 11 M0.081.412 TU, provided that the owner observes the operating rules set out in the instruction manual.
The warranty period for the charger "Impulse ZS-01" is 24 months from the date of sale through a retail network.
In the absence of the date of sale and the stamp of the store in the warranty and tear-off coupons, the warranty period is calculated from the date of release of the product by the manufacturer.
During the warranty period, the owner has the right to free repair upon presentation of the warranty card. At the same time, for the first repair of each year, a tear-off coupon is cut out corresponding to the work performed. Repairs that follow during the warranty period are also performed free of charge, and data on the type of repair is recorded on the back of the warranty card and on the accounting and technical card, which is located in the repair company.
Repair of the product is carried out by repair companies, information about which can be found in the radio store.
Without the presentation of the warranty and tear-off coupons or in case of violation of the e-protection policy on the product, claims to the quality of work are not accepted and warranty repairs are not performed.
During the warranty period of operation established for the product, repairs are made at the expense of the owner if he does not operate it in accordance with this instruction manual or does not follow the recommendations of the repair company aimed at ensuring the normal operation of the product.
The exchange of faulty devices is carried out through the distribution network upon presentation of a certificate from the repair company and a warranty card in accordance with the current rules for the exchange of industrial goods purchased in the retail network of the state and cooperative trade.
For comments and suggestions on the quality of products, please contact the address: 325027 Kherson-27, P.O. Box No. 35.
First, some theory...
The impulse massager is intended for massage, weakening and relieving pain by the method of transcutaneous low-frequency impulse action on the muscles. It can be used to relax various parts of the body, to relieve muscle fatigue, to improve blood circulation in the skin area, to soften muscle pain. Also, with proper (point) use, it has a healing effect.
The massager allows you to massage using 5 modes for certain areas of the body and four program modes of impulse exposure to areas of the body. To limit the time of massage exposure, the electronic unit of the device has a function to limit the massage time. The intensity (strength of impulses) and frequency of exposure are adjusted by the user using the controls on the device, depending on the individual sensations and the goals of the massage (relaxation, stimulation or pain relief).
The standard massage time for one area is 10-15 minutes. A full massage session should not exceed 30 minutes. The standard number of sessions per day is 1-2 for the first week of use. Some people may feel tired. In this case, you need to reduce the intensity, reduce the time and number of sessions, or even stop using the massager.
The parcel was sent by mail Laos (full name - Lao People's Democratic Republic - a state in Southeast Asia with the capital Vientiane. In the west it borders on Thailand, in the east - with Vietnam, in the south - with Cambodia, in the north - with the Yunnan province of China , in the northwest - with Myanmar - approx. author), thanks to which, the delivery time took only 15 days
Track number
The massager comes in a thick cardboard box, inside everything is neatly laid out, thanks to a plastic insert.
Inside the box, as expected, the seller put instructions for using this massager and a sheet with points on which it is recommended to make an impact during the massage
Documentation
Instructions for use (English):
List of active points on the human body (English / Chinese):
point description... 
As for the product package, it is as follows:
- The electronic unit
- Charger
- USB wire
- 3 AA batteries PenesamiG
- Flexible cord for connecting electrodes (2 sets)
- Two sets of electrode plates (electrodes)
- Rubber Shoes
- User manual
- Sheet with a list of active points
Well, I could not help but pay attention to the batteries. These are the very "finger" batteries PenesamiG
Device dimensions, weight
Let's go directly to the electronic unit. Or rather, his insides. We disassemble the control unit. To do this, take out the batteries and unscrew the two bolts on the back cover of the unit:
Reverse side of the board
The soldering is very good, the smd components are soldered very well. There are traces of flux on the board, or rather the fingerprints of the Chinese
front view
As I mentioned earlier, in addition to batteries, the kit comes with a power supply (in the instructions for use it is stated that the supply voltage is 4.5V). I did not find any identification marks on the power supply, so I decided to take a closer look at it:
The minimum number of components. “The main thing is that it works, well, okay” - the motto of the Chinese when assembling such blocks
Let's take some basic measurements:
I took out a multimeter, in the morning I took a few measurements. The voltage supplied by the power supply is 3.27V. Well, I think, by the evening I will take measurements under load and measure the current strength with voltage, at the same time I will take a few photos with the results. I just plugged the power supply into the network, there was a bang and what was to be expected from it. I dismantled it, a step-down transformer melted from visual defects, the output capacitor heated up very much (I took a photo of the temperature 5 minutes after the incident)
To be honest, I wasn't upset at all. The massager perfectly performs its functions, powered by "finger-type" batteries. The power supply went to the far box.
Before proceeding to the principle of operation of the device, I want to highlight a few caveats when using a pulsed massager:
The massager cannot be used in conjunction with transplantable medical electronic devices, such as:
- pacemaker;
- with electronic life support devices, such as respirators;
- with medical electronic devices attached to the body, such as an electrocardiograph.
- during an acute illness;
- in the presence of a malignant tumor;
- during an infectious disease;
- during pregnancy;
- with heart disease;
- during high temperature;
- with abnormal blood pressure;
- in violation of the sensitivity of the skin or skin disease;
- if you are receiving other treatment, especially if you experience unusual sensations.
So, now I want to talk about the functionality of the device. Since there is a lot of information, I will remove it under the spoiler
About the massage...
First, you need to connect the electrode. If this is not done, after 7 seconds the machine will enter standby mode and turn off the power. Now we will use the "Arms and Legs" mode and consider four program modes of impulse action on body parts 
On rubber shoes there are three plastic points, which are one of the components of foot massage. Points allow you to direct impulses to the right place on the foot 
To begin with, turn on the device and select the mode we need (from 1 to 7, OFF - shutdown) 
Next, in order: 
Group1
Mode 1. Shoulder 
Mode 2. Waist (Waist) 
Mode 3. Joint (Joint mode, Joints) 
Mode 4. Hand and Foot (Hands and foot) 
Mode 5. Leg (Legs) 
Mode 6. Repeat 
Group 2
Mode 1. Press 
Mode 2. Rub (Rubbing) 
Mode 3. Vibrate (Vibration) 
Mode 4. Thump 
Each mode has its own speed. A special key will allow you to increase the speed of the mode or decrease it. 
To take these photos, I had slippers on my feet. Different modes give different sensations. But after all these manipulations, the leg looks like this: 
Well, now, some photos taken when testing the device:
"Hand and Foot" mode "Thump" effect on the body
Mode "Leg" impact on the body "Rub"
“Shoulder” mode impact on the body “Press”
pros
- Good build quality
- Intuitive interface
- Possibility of customization
- Powered by AA batteries / Power supply
- Burnt power supply (I'm sure this is an isolated case)
- Large control box
PS When testing the massager, no one was hurt. take care of yourself
I plan to buy +16 Add to favorites Liked the review +17 +33The principle of operation of the device
The device generates impulse currents of a certain strength and frequency. When two electrodes are applied to the skin, currents arise between them that pass through the tissues of our body.
The low-frequency or high-frequency electrical stimulation created by the device acts on the nerve fibers, strengthening or weakening the nerve impulses. Thus, it is possible both to stimulate muscle contraction, and vice versa, to relax them.
Electrical stimulation improves blood and lymph circulation, activating the delivery of necessary substances to cells and the removal of "all unnecessary" from body tissues. Electric currents can effectively block the conduction of pain impulses, as well as affect the very cause of pain.
"Stimulus" can be practically indispensable in cases where a person does not have the opportunity to fully force his muscles to work. For example, bedridden patients or weakened.
Conversely, a soothing massage can be useful after heavy physical exertion, to relieve muscle “clamps” during sedentary work.
How Stimulus works
When you put electrodes on a certain area of your body and turn on the device, pulsed currents of a certain frequency and strength are formed between the electrodes. You can adjust the frequency and strength of the pulses yourself.
Electrical impulses affect your body - skin, subcutaneous tissues, muscles, nerves, blood vessels. The currents affect the most important life processes - the work of the lymphatic and blood capillaries, the contraction of muscle fibers, the conduction of nerve impulses, the inter- and intracellular transport of substances, chemical processes, the properties of liquids, and much more.
In certain cases, this effect is the most effective treatment method of all known.
"Stimulus" is able to have both a tonic effect on the tissues of the body, and a relaxing one. It all depends on the strength and frequency of the pulses that the device generates. And you can control these parameters yourself. Moreover, the device is very easy to use.
"Stimulus" is a massager. We all know that traditional massage is a physical effect on our body. Massage can be both stimulating, warming (for example, for athletes before training), and relaxing. As a rule, during the massage, one person “kneads” the body of another person with his hands. At the same time, in the “massaged” tissues, the work of blood and lymphatic vessels, the circulation of fluids, the work of nerve fibers, and so on, improve. But all these effects can be achieved not only by mechanical action, but also by electrical. After all, all our internal processes are of an electrical nature and are well studied by science.
The transcutaneous electric impulse massager "Stimulus" was developed by Siberian scientists on the basis of human physiology and biochemistry data and is an effective physiotherapeutic device. "Stimulus" has passed a number of clinical trials and proved its effectiveness in practice. The device is safe to use and can be used both in a hospital and at home.
Several NOT
During the day, you can use different physiotherapy devices, but, just in case, you should not use them at the same time. To each his own time.
In some situations, before using the "Stimulus" need to consult a doctor:
- during an acute illness;
- in the presence of a malignant tumor;
- during pregnancy;
- in diseases of the heart.
Not it is desirable to apply electrodes to the region of the heart, to the bare area near the mouth, or to parts of the body with damaged skin.
If during a massage session you want to move the electrodes to another part of the body, first turn off the device.
Not
use "Stimulus" simultaneously with other electronic devices.
Not
use the device while sleeping.
Not
apply and do not lean the electrodes against metal objects - jewelry, buckles, zippers and others.
Not
use the device on one area of the body for more than 30 minutes.
Increase the power of the device during the session NOT abruptly, but gradually.
Some general rules application of "Stimulus"
The optimal time for one session is 5-10 minutes. After 15 minutes, the device automatically turns off the pulses, since prolonged stimulation causes muscle fatigue.
Standard number of sessions: 1-2 per day for the first week of use. Then the number of sessions can be increased.
Adjust the strength of the impulses yourself. The rule "the stronger the better" is not always true. Excessive intensity of pulses can lead to discomfort, irritation or redness of the skin.
Focus on your own feelings. The use of the device should not cause too much discomfort or pain. You can always reduce the intensity of the impulses and reduce the session time.
Reusable electrodes. The duration of the electrodes is theoretically unlimited.
Remember that current only occurs between TWO electrodes!
Applying only one electrode and trying to check the operation of the device is pointless.
- Electronic block - 1 pc.
- Electronic cord with safety plug - 1 pc.
- Durable electrodes 2 pairs
- Velcro tape for attaching electrodes - 1 pc.
- Batteries AAA - 2 pcs.
- Operation manual - 1 pc.
- CD with video instructions - 1 pc.
It is very easy to use the device. This does not require special knowledge and skills. Apply electrodes to the "problem" area and get the desired effect!
- LCD display
- Impact intensity level
- Exposure mode
- Exposure frequency
- Control Panel
- Enable/Boost button
- Disable/Release button
- Mode switch button
- "Intensity/Frequency" setting switch button
Button"Enable/Boost"
All indicators on the indicatorsdisplay grow | 1. Turn on the device. 2. When setting the intensity - increases the intensity of the impulses. Right indicator a 3. When setting the frequency - increases the frequency of the pulses. Left indicator With |
|
Button"Turn off/Loosen" If indicatorsintensity orfrequency of exposure is higherunits, pressing a button"Off" gives the device"Release" command | 1. Turn off the device 2. When adjusting the intensity, reduces the intensity of the pulses 3. When setting the frequency, reduces the pulse frequency To turn off "Stimulus", firstminimize impactimpulses |
|
| Switch Mode button | Sequentially switches eight exposure modes:
|
1. Tapping mode |
||
2. "Knead" mode |
||
3. Rubbing mode |
||
| Toggle Intensity/Frequency Settings button
| intensity only possible with the "On" buttons. (boost) or "Off" (let loose) 2. Press once, the intensity mode will turn on. Right indicator a 3. Pressing this button again allows you to adjust the Frequency of exposure. Left indicator With |
A few basic rules for working with the device
1. To avoid electric shock, make sure that during the session, metal objects (chains, buckles, bracelets, buttons, watches, etc.), as well as water, do not come into contact with the electrodes.
2. To ensure maximum contact and, consequently, the effect of beneficial effects, the skin areas for applying the electrodes, as well as the surface of the applied plates, must be clean.
3. Increasing the frequency and power of the impact of electrical impulses should be gradual, remaining within the comfort of sensations.
4. Disconnection of one of the electrodes for more than seven seconds turns off the device.
5. In order for the device to bring you benefit and pleasure for many years, you should carefully study the instructions in the part “VERY IMPORTANT!” (page 3).
The intensity level of exposure shows the intensity (strength) of electrical impulses | You can independently choose the strength of the impulses: |
|
The exposure mode shows the "massage" mode, tuned to a specific area of the body | You can independently choose the massage mode for a certain part of the body by successively pressing the "Mode" button |
|
Frequency of electrical impulses: from low to high frequency: 1 bar - minimum (lowest frequency), 10 bars - maximum | You can choose the frequency of the impulses yourself by pressing the "On" button in sequence to increase, or "Off" to weaken the frequency of exposure |
|
Displays the time remaining until the end of the session |
||
Modes of influence basic: Tapping, kneading, rubbing | If the mode is enabled, its icon flashes on the display screen. The flashing speed depends on the set exposure frequency. |
|
 | Flickering mode indication "Tapping" | Shoulders, Arms and Legs |
 | Flickering mode indication "Knead" | The flickering of the same icons means work in modes "Loin" and "Joints" |
 | Flickering mode indication "Trituration" |
Place the electrodes on the area of the body that you want to massage.
Keep in mind that the massage effect occurs on the area of the body between the electrodes. The greater the distance between the electrodes, the greater the area we will cover with a massage effect. But even if the distance between the electrodes is too large, the efficiency of the device may decrease. Optimal distance 20- 30 cm. To secure the electrodes, use the fixing tape (included), elastic bandage or adhesive tape. In cases where electrodes are applied to the back, you may need the help of another person.
 | Placement of electrodes on the shoulder area.
|
|
 | Applying electrodes to the lumbar area
|
|
 | Placement of electrodes on the hands
|
|
 | Applying electrodes to the legs (Feet)
|
|
 | Applying electrodes to the legs (calves)
|
|
 | Applying electrodes to the area of the joints
|
|
 | Placement of electrodes on the back
|
1. The device is powered by two AAA batteries. It can be batteries or accumulators. Insert the correct polarity into the battery compartment on the underside of the instrument.
2. Batteries included in the scope of delivery are intended only for testing the device. Their service life can be less than a month.
3. If the device is not used for a long time - remove the batteries.
4. If the device does not turn on or you notice that the massage effect has weakened, replace the batteries.
5. The average life of one set of conventional batteries with a single daily use of the device is approximately 3 months.
1. Make sure the device is turned off.
2. Insert the plug of the electrode cord into the appropriate socket on the instrument.
3. Gently insert the pin ends of the cord into the holes on the electrodes. The color of the tips does not matter.
4. The surface of the electrodes must be dry and clean.
5. Do not use the device if the electrodes or the electrode cord are damaged.
1. Place the electrodes at some distance from each other on the area of the body chosen for massage. The skin at the application site must be clean and dry. Do not bend the electrodes.
2. Fix the electrodes with the fixing tape included in the kit. You can also use an elastic bandage or adhesive tape.
3. Turn on the device with the "Enable / Boost" button. The device will immediately turn on in the “Tapping” mode. At the same time, the strength and frequency massage impulses will be minimal.
4. Select the desired massage mode with the "Switch mode" button. You will read about the modes of the device below.
5. Adjust the intensity and frequency with the On/Boost and Off/Lower buttons. And the adjustable parameter itself - intensity or frequency, select the "Intensity / Frequency" button.
6. Do not remove the electrodes during the session. If this happens, the device will automatically turn off after 7 seconds.
7. After the end of the massage session, turn off the device and remove the electrodes.
We remind you that the device automatically turns off after 15 minutes of operation!
Stimulus has several programs that can operate in several modes.
For an example of programming and setting up STIMULUS, consider a mode that helps to get rid of muscular and neuralgic pain in the back and lower back, as well as numbness.
We use the "Combined for the lumbar" mode.
|
1. Place the plates symmetrically on the part of the back where you are experiencing pain, so that the spine is between the electrodes, as shown in the figure. |  |
|
2. Turn on the massager. On button. | |
|
3. Press the "Mode" button 4 times in a row. |  |
|
|
|
4. Press the "I / CH" button - the ability to control will turn on intensity exposure (the indicator in the RIGHT lower corner reflects the level in the form of the number of strips. Minimum 1, maximum ten). |  |
|
5. Press the "On" button raise the INTENSITY (power of IMPACT) to the desired level. |  |
|
If we “went through” with the power of exposure, we return it to a comfortable level by successively pressing the “Off” button. |
|
|
6. Press the "I/Ch" button again - the ability to control will turn on Frequency exposure (the indicator in the lower LEFT corner reflects the level in the form of a number of bars). |  |
|
7. Press the "On" buttons and "Off" adjust the Frequency (speed of pulses) to an effective and comfortable level. |  |
A fragment of the Silhouette in the lumbar region will flash on the screen. Always use only clean plates.
Do not bend the plates. Avoid touching the plates with metal objects such as belt buckle, chain, etc.
tapping improves blood circulation | Single impulses |
|
kneading relieves fatigue | Short series of high frequency pulses.
|
|
Trituration gradually relieves neuralgia or muscle pain | Long series of pulses |
 | Combined mode for the shoulder girdle
|
|
 | Combined mode for the lumbar
| The intensity and frequency to a comfortable but effective level are adjusted in the same way as in the previous modes using the buttons |
 | Combined mode for hands
| The intensity and frequency to a comfortable but effective level are adjusted in the same way as in the previous modes using the buttons |
 | Combined mode for the joints of the hands and feet
| The intensity and frequency to a comfortable but effective level are adjusted in the same way as in the previous modes using the buttons |
 | Combined mode for legs
| The intensity and frequency to a comfortable but effective level are adjusted in the same way as in the previous modes using the buttons |
General rules
Session time. The optimal number of sessions and the level of intensity of exposure.
The standard massage time for one area is 10-15 minutes. A full massage session should not exceed 30 minutes, and for this you will have to turn on the device again.
Optimal number of sessions: 1-2 per day.
The choice of intensity and frequency depends on the physical condition of the person. Therefore, these parameters are selected individually. In the first few days of use, determine the massage regimen that is most comfortable for you by trying different intensity and frequency of exposure. If you feel tired or uncomfortable after a massage, reduce the intensity and frequency of the impulses next time, or shorten the session time.
Please note that the intensity of exposure may vary depending on the battery level and condition of the electrodes.
Preparing the instrument for storage
- Switch off the device and unplug the cord from the device.
- Roll up the elastic bandage.
- Carefully, without bending the electrode cord and the electrodes and avoiding the electrode pin being torn, wrap the electrode cord around the electrodes.
Care and storage of the device
- Keep the device out of the reach of children.
- It is not advisable to expose the device to high humidity, high temperature, direct sunlight, strong electromagnetic fields.
- In case of long-term storage of the device, it is necessary to remove the batteries from it.
- If the electrodes become dirty, clean them with a damp cloth or cotton pad. Do not use hot water, detergents or chemicals, liquids containing alcohol or other solvents. Do not scrape the surface of the electrodes with your nails or brush.
- Keep all parts of the instrument in the packing box along with this manual.
- Before cleaning the appliance, be sure to turn it off and unplug the power cord.
- Wipe the device with a soft cloth. If the instrument is heavily soiled, wipe it with a damp cloth. Wipe dry. Make sure that water does not get inside.
- Do not use benzine or thinner to clean the instrument.
In case of non-compliance with the operating rules, the manufacturer is not responsible for the performance of the device!
Trouble-shooting
MALFUNCTION | THE REASONS | ELIMINATION |
The device does not turn on | Batteries installed incorrectly or out of charge | Install the batteries, observing the polarity. Replace batteries |
Appliance switches off too quickly | The electrodes are loose | Place the electrodes on the skin surface correctly (otherwise the device will turn off automatically) |
The device turns off during the procedure | The plates have moved away from the body | Switch off the device before removing the electrodes from the skin |
Weak or discharged batteries | Install new batteries with correct polarity. |
|
Faulty electrode cord | Replace Cord |
|
Stimulation is not felt | Electrodes placed on wet skin | Wipe dry the surface of the skin where the electrodes are placed |
The electrodes have been stored at too high a temperature, high humidity, or in direct sunlight. | Put the electrodes in the refrigerator overnight |
|
Press the electrodes closer to the skin |
||
Electrodes touch each other | Place the electrodes on the body correctly as described earlier in this manual |
|
Cord connected incorrectly | Check if the cord is connected correctly |
|
Intensity set too low | Turn up the intensity |
|
Battery power is too weak | Install new batteries |
|
Damage to the electrode surface | Replace electrodes with new ones |
|
skin redness skin irritation | Session time is excessive | Reduce session time |
The electrodes are loosely applied to the body | Check electrode tightness |
|
The electrode surface is dirty | Clean the electrodes from contamination |
MANUFACTURER'S WARRANTY
The warranty period of the device is 12 months from the date of sale, but not more than 36 months from the date of manufacture.
During the warranty period, in case of detection of defects that have arisen through no fault of the consumer, the manufacturer provides warranty service for the device (repair or replacement) at its own expense.
Warranty service is subject to the following conditions:
- availability of a completed certificate of acceptance and sale;
- unexpired warranty period;
- safety and compliance of the device marking with the date of manufacture,
- specified in the certificate of acceptance and sale;
- no damage to the device, gas-filled electrode and connecting cord;
- no traces of moisture, contamination of the device;
- no signs of opening the device.