Simple at first glance, the bike hides a large number of interconnected mechanisms. The serviceability of each of them guarantees comfortable and safe trips, and the two-wheeled horse itself is used as a full-fledged transport.
Periodic maintenance is required to keep your bike in excellent condition. How often you need to carry out cleaning, overhaul and repair activities depends on many factors. Among them are the features of the model, the quality of components, the duration of trips and the style of riding.
An easy way to troubleshoot, change parts and consumables in a timely manner is to contact a qualified workshop. In some cases, this is the only option to bring the bike to a ready state. However, most bike maintenance can be done by yourself. By spending time, the bike owner will gain invaluable experience and save a considerable amount.
General rules for bike care
Store Bought new bike begins to slowly “get used” to its new owner: the moving nodes are rubbed in and the fixed ones are getting stronger. Lubrication plays an important role in the quality of work of all parts and joints. Over time, it absorbs particles of metal chips and dirt. When the capacity of the lubricant composition exceeds the allowable one, it loses its properties and begins to work to the detriment of the mechanisms. As a result, increased wear.
First and most important rule when - keep it clean and pay great attention to the lubrication of rubbing mechanisms. Systems approach to keeping great in working condition, it is:
- timely and thorough washing;
- dust removal of sensitive parts - bushings, carriage assembly, switches;
- removal of used grease and stains;
- treatment with special lubricants;
- timely removal of foci of corrosion;
- ensuring the geometric integrity of the structure - careful tightening of all bolted connections.
It is very important to properly store your bike. In the off-season, the bike is idle, and its condition will directly depend on the surrounding conditions. It is not recommended to keep on the balcony in the cold season and in damp rooms. It should be clean around the bike, and it is also a good idea to provide him with a little space. If you cannot create optimal storage conditions, you can disassemble it and place it in an airtight case.
The condition of the frame, wheels and mechanisms is negatively affected by the fall of the bicycle. Of course, with active skiing this is inevitable, and at home it can accidentally fall on its side or even fall off the wall. However, it is best to keep flying to a minimum, handle the bike more carefully and choose safer places to ride.
Actually, all of the above is general bike maintenance. This allows you to increase the service life of all parts and maintain a decent appearance. But over time, you will have to delve into the details of the bicycle device and deeper.
Repair Tools & Consumables
It is impossible to carry out bulkhead and repair work with your own hands without a set of tools. Conventionally, they can be divided into mandatory and special. The first ones will be needed one way or another for all types of repair work.
Basic maintenance tools:
- spanners different sizes+ movable wrench;
- hexagons (choose the appropriate sizes);
- flat and Phillips (you will need more often) screwdrivers;
- pliers for "rough" work;
- blades for disassembling the wheel;
- thin knitting needles;
- clamps;
- pump;
- tire repair kit.
Cyclist repair case
Additional tools are required for professional repair mechanisms. For example, the bulkhead of a carriage or a system of transmission stars cannot be carried out only with a screwdriver or an ordinary wrench.
Bicycle repair kit includes:
- pullers of connecting rod pair and carriage;
- cassette puller with whip;
- crank puller;
- chain wrench;
- key for adjusting the tension of the spokes;
- scissors for cutting cables;
- repair kit for pumping hydraulic brakes;
- chain washing;
- oil dosimeter (for special parts) and measuring cup.
This is what the cassette remover looks like
The tool is acquired once and for all, it helps to improve the technical condition of a single mechanism. Consumables play a role in maintaining the mechanism during operation, while they themselves become unusable. Bicycle accessories include:
- different kinds lubricants: water and dirt-repellent for the chain and sprockets, for the suspension fork, thickened compounds for bearings;
- cleaners;
- brake fluid (for hydraulics);
- sealants;
- rooster;
- brake pads;
- cables and springs.
Timely update Supplies together with the use of the right tools guarantees 100% good condition of the mechanisms.
Frame, wheel and suspension maintenance
We begin the maintenance of individual fixed parts of the bike. The frame is the main component, without which the great does not exist in principle. The frame takes on all the efforts from both the person and all the constituent parts.
Over time, fatigue accumulates in the pipes and joints, which forces the frame to distort its shape. It is worth noting that this is noticeable only after a very long use of the bike. Conditions that cause frame distortion: Riding in unintended conditions, frequent falls of the bike, inconsistency in load capacity for the weight of the cyclist.
The frame is also vulnerable to corrosion. Chips and cuts on the paint cause intense oxidation of the metal. To prevent the development of rust, it is necessary to frequently inspect the frame, eliminate pockets of corrosion with special compounds, and, if necessary, prime and paint the problem area.
Serious damage (cracks and breaks) cannot be repaired with your own hands, here you should contact the master.
Wheels are prone to warping. Rim bends make driving uncomfortable and worsen the condition of the wheel. or "egg" can be done by changing the tension of the spokes with.
Wheel bending can be avoided by maintaining optimal tire pressure. The tubes and tires should be free of cuts and punctures, and the nipple should seal the air inside the tire. If the puncture is caught on the way, you need to use a repair kit - special patches for sealing holes.
Blades for dismantling the wheel
Requires careful care and the central part of the wheel - the sleeve. Bushing maintenance features:
- do not wash under strong pressure of water;
- periodically wipe off dust and apply clean lubricant;
- when turning the wheel, open, replace the bearings and lubricate the internal cavities.
Maintenance of the front fork includes periodic replacement of grease, cleaning the legs from dust and plaque, and timely replacement of sealing parts. In some cases, when the softness of the shock absorber is not adjustable, it is necessary to replace the spring and / or damper. Maintain cushioning mountain bike in working condition is extremely important, as it plays a key role in the comfort of movement and the condition of the frame.
Some bicycles, in addition to the suspension fork, have a rear vibration damper. The requirements for caring for it are similar, except that you often have to wipe the anthers from dirt.
Overhaul of the steering column, brake system and transmission
We turn to the elements of the bike, which provide clarity of control, movement and stopping.
Steering column
There are two types of columns on bicycles - integrated with industrial bearings and semi-integrated with balls.
Semi-integrated steering column bearing assembly
Maintenance of a steering wheel with industrial bearings includes only timely lubrication. With semi-integrated columns, everything is more complicated: over time, the loads inside it are redistributed, as a result of which the balls crumble. As a result, turning the steering wheel or its difficult course. Bulk ball steerer repairs include replacing them and thoroughly lubricating them. Also, it will not be superfluous to check the column for dirt. Work must be carried out before each season or as needed.
Brake system
Maintaining the brakes in working condition is a guarantee of safety. System checks should be carried out as often as possible, on average twice a week. We check:
- pad wear;
- condition of the braking surface;
- integrity and tension of cables;
- lubrication of the moving parts of the caliper and handle;
- line to air (for brakes with hydraulics).
For effective braking, it is important to set the pads correctly: the gap should be minimal, but not slow down the wheel. Of course, there should be no curvature on the rim itself. The surface (rim or disc) must be wiped clean and free from oil or contamination.
Adjusted rear disc brake clearance
from tension and general condition ropes depends on the accuracy and speed of braking. Optimal tension - the pads instantly fit and bounce when you press / release the handle. Of great importance is the good condition of the jacket - no cracks on the shell and winding stretch marks.
For hydraulic brakes, it is necessary to keep the line in working condition. The reason for poor performance lies in the presence of air or fluid contamination. The system is bled using a special tool once a season. The fluid must comply with the manufacturer's instructions.
Transmission overhaul:
- checking and replacing bearings in the carriage, lubricating the assembly;
- inspection of the integrity of the connecting rods;
- cleaning and;
- checking and replacing the stars on the cassette;
- switch setting.
It is possible to dismantle the carriage and connecting rods only with the help of special pullers. Particular attention is paid to the condition of the connecting rod pair (there should be no cracks) and the condition of the bearings inside the bottom bracket. The key role is played by abundant lubrication with a special compound.
Cleaning and lubricating the chain is necessary to reduce wear on expensive transmission components - cassettes. it can be done manually with a lock or with the help of a squeeze. It is necessary to service the transmission mechanism as necessary, however, it will not be superfluous to periodically wipe the surface of the stars and chains from dust.
Chain release wrench with screw
Worn chainrings on cassettes can be replaced individually. To release the axle rear wheel from the system, you will need a special puller key with a chain whip to hold it.
Bicycle maintenance - keeping it clean, lubricating the mechanisms, replacing worn parts and consumables - is an integral part of the life of a cyclist. Timely correction of all shortcomings, careful handling and foresight allows you to get the most out of the bike and enjoy riding for many, many seasons.
Task 1 of 15
1 .
Are the Rules violated in the situations depicted?
Correctly
f) tow bicycles;
Not properly
6. Requirements for cyclists
6.6. The cyclist is prohibited from:
d) hold on to another vehicle while driving;
f) tow bicycles;
Task 2 of 15
2 .
Which cyclist does not break the rules?
Correctly
6. Requirements for cyclists
6.6. The cyclist is prohibited from:
Not properly
6. Requirements for cyclists
6.6. The cyclist is prohibited from:
b) move on motorways and roads for cars, as well as on the carriageway, if there is a nearby Bike Lane;
Task 3 of 15
3 .
Who must give way?
Correctly
6. Requirements for cyclists
Not properly
6. Requirements for cyclists
6.5. If the cycle path crosses the road outside the intersection, cyclists must give way to other vehicles moving on the road.
Task 4 of 15
4 .
What loads are allowed to be carried by a cyclist?
Correctly
6. Requirements for cyclists
22. Shipping
Not properly
6. Requirements for cyclists
6.4. The cyclist can only carry such loads that do not interfere with the control of the bike and do not create obstacles for other participants. traffic.
22. Shipping
22.3. Carriage of cargo is permitted provided that it:
b) does not violate the stability of the vehicle and does not complicate its management;
Task 5 of 15
5 .
Which cyclist violates the Rules when carrying passengers?
Correctly
6. Requirements for cyclists
6.6. The cyclist is prohibited from:
Not properly
6. Requirements for cyclists
6.6. The cyclist is prohibited from:
e) carry passengers on a bicycle (with the exception of children under 7 years of age who are transported on an additional seat equipped with securely fastened footrests);
Task 6 of 15
6 .
In what order will the vehicles pass through the intersection?
Correctly
16. Passage of intersections
Not properly
16. Passage of intersections
16.11. At the intersection of unequal roads, the driver of a vehicle moving along a secondary road must give way to vehicles approaching this intersection of carriageways along the main road, regardless of the direction of their further movement.
16.12. At the intersection of equivalent roads, the driver of a non-rail vehicle must give way to vehicles approaching from the right.
This rule should be guided by each other and tram drivers. At any unregulated intersection, a tram, regardless of the direction of its further movement, has an advantage over non-rail vehicles approaching it along an equivalent road.16.14. If the main road changes direction at the intersection, the drivers of vehicles moving along it must be guided by the rules for passing the intersections of equivalent roads.
This rule should be guided by each other and drivers moving on secondary roads.Task 7 of 15
7 .
Cycling on sidewalks and footpaths:
Correctly
6. Requirements for cyclists
6.6. The cyclist is prohibited from:
Not properly
6. Requirements for cyclists
6.6. The cyclist is prohibited from:
c) move along sidewalks and footpaths (except for children under 7 years old on children's bicycles under adult supervision);
Task 8 of 15
8 .
Who has the right of way at the intersection with the bike lane?
Correctly
6. Requirements for cyclists
6.5. If the cycle path crosses the road outside the intersection, cyclists must give way to other vehicles moving on the road.
Not properly
6. Requirements for cyclists
6.5. If the cycle path crosses the road outside the intersection, cyclists must give way to other vehicles moving on the road.
Task 9 of 15
9 .
What distance should be between groups of cyclists moving in a column?
Correctly
6. Requirements for cyclists
Not properly
6. Requirements for cyclists
6.3. Cyclists, moving in groups, must ride one after another so as not to interfere with other road users. A column of cyclists moving along the carriageway should be divided into groups (up to 10 cyclists in a group) with a distance of 80-100 m between groups.
Task 10 of 15
10 .
Vehicles will pass the intersection in the following order
Correctly
16. Passage of intersections
16.11. At the intersection of unequal roads, the driver of a vehicle moving along a secondary road must give way to vehicles approaching this intersection of carriageways along the main road, regardless of the direction of their further movement.
Not properly
16. Passage of intersections
16.11. At the intersection of unequal roads, the driver of a vehicle moving along a secondary road must give way to vehicles approaching this intersection of carriageways along the main road, regardless of the direction of their further movement.
16.13. Before turning left and making a U-turn, the driver of a non-rail vehicle is obliged to give way to a tram in the same direction, as well as to vehicles moving on an equivalent road in the opposite direction straight or to the right.
Task 11 of 15
11 .
The cyclist passes the intersection:
Correctly
16. Passage of intersections
Not properly
8. Traffic regulation
8.3. The traffic controller's signals take precedence over traffic lights and road sign requirements and are mandatory. Traffic lights other than flashing yellow take precedence over road signs priority. Drivers and pedestrians must comply with the additional requirements of the traffic controller, even if they contradict traffic signals, traffic signs and markings.
16. Passage of intersections
16.6. When turning left or turning around at the green signal of the main traffic light, the driver of a non-rail vehicle is obliged to give way to a tram in the same direction, as well as vehicles moving in the opposite direction straight or turning right. This rule should be guided by each other and tram drivers.
Task 12 of 15
12 .
Flashing red signals of this traffic light:
Correctly
8. Traffic regulation
Not properly
8. Traffic regulation
8.7.6. To regulate traffic at railway crossings, traffic lights with two red signals or one white-moon and two red signals are used, having the following meanings:
a) flashing red signals prohibit the movement of vehicles through the crossing;
b) a flashing white-moon signal indicates that the alarm system is working and does not prohibit the movement of vehicles.
At railway crossings, at the same time as the prohibitory signal of the traffic light, an audible signal may be turned on, additionally informing road users about the prohibition of movement through the crossing.
Task 13 of 15
13 .
The driver of which vehicle will pass the intersection second?
Correctly
16. Passage of intersections
16.11. At the intersection of unequal roads, the driver of a vehicle moving along a secondary road must give way to vehicles approaching this intersection of carriageways along the main road, regardless of the direction of their further movement.
16.14. If the main road changes direction at the intersection, the drivers of vehicles moving along it must be guided by the rules for passing the intersections of equivalent roads.
This rule should be guided by each other and drivers moving on secondary roads.
Not properly
16. Passage of intersections
16.11. At the intersection of unequal roads, the driver of a vehicle moving along a secondary road must give way to vehicles approaching this intersection of carriageways along the main road, regardless of the direction of their further movement.
16.14. If the main road changes direction at the intersection, the drivers of vehicles moving along it must be guided by the rules for passing the intersections of equivalent roads.
This rule should be guided by each other and drivers moving on secondary roads.
16 Crossings
Not properly
8. Traffic regulation
8.7.3. Traffic lights have the following meanings:
A signal in the form of an arrow, allowing a left turn, also allows a U-turn, if it is not prohibited by traffic signs.
The signal in the form of a green arrow (arrows) in the additional (additional) section (sections), turned on together with a green traffic light, informs the driver that he has an advantage in the direction (directions) of movement indicated by the arrow (arrows) over vehicles moving from other directions;
f) a red signal, including a flashing one, or two red flashing signals prohibit movement.
A signal in the form of a green arrow(s) in the additional (additional) section(s) together with a yellow or red traffic light signal informs the driver that traffic is allowed in the indicated direction, provided that vehicles moving from other directions are allowed to pass unhindered.
The green arrow on the plate, installed at the level of a red traffic light with a vertical arrangement of signals, allows movement in the indicated direction when the red traffic light is on from the rightmost lane (or the leftmost lane on roads with one way traffic) subject to the provision of an advantage in movement to its other participants moving from other directions to a traffic light signal allowing movement;
16 Crossings
16.9. While driving in the direction of the arrow switched on in the additional section at the same time as the yellow or red traffic light, the driver must give way to vehicles moving from other directions.
While driving in the direction of the green arrow on the table set at the level of the red traffic light with a vertical arrangement of signals, the driver must take the extreme right (left) lane and give way to vehicles and pedestrians moving from other directions.
In order for the bike to be a source of joy for its owner, it is necessary to constantly make certain efforts. In particular, regularly perform maintenance of the bike. Inspections should be carried out at least 2 times a year, or even more often if you often drive off-road and ride in winter.
Bike maintenance before the season
If you decide to service the bike before the start of the season, you need to check the performance of every detail.
When inspecting the frame and front fork, make sure that there are no cracks, scratches, dents or other defects on them.
When checking the steering wheel, hold the front wheel between your knees, the steering wheel with the take-out should be in a straight line with them. Turn the steering wheel in different directions, it should not move. There should be plugs at the ends of the steering wheel.
Use solvent-free liquid lubricants and lubricate all components and the chain. After checking the suspension and adjusting it, tighten all the screws. Make sure the saddle does not move in relation to the frame and post and is parallel to the ground. Don't forget to check your tire pressure. You will see the recommended value on the tire - on the side.
Video instruction for bike maintenance before the season
Bike maintenance before winter
At the end of the season, you should wash your bike, then take care of the brake cables and jackets, joints and derailleurs - lubricate them, remove the chain and store it, after cleaning it using special machines or immersing it in a bottle of kerosene. If necessary, write down all the data from the cycle computer. Spring and pneumatic mechanisms must be removed from the load. Release the tire pressure to one and a half atmospheres, loosen the pressure in the air fork chambers, loosen the shift cables, and release the brakes.
Video instruction for maintaining a bicycle for winter
Bike storage features
If you don’t want your bike to turn into unpleasant surprises in the future, keep it in the apartment. If you do not have enough space, then hide it under the bed, in the closet and so on. Please note that in specialized stores it is quite inexpensive to purchase special fasteners with several hooks. The best option It counts as just hanging the bike to the wall.
An attic, garage, balcony and other premises should not be chosen for storing a bicycle. Since in this case your iron friend will be exposed to constant weathering. In the case of regular changes in humidity and temperature, its systems and elements will deteriorate. Tires will also be damaged.
A warm vestibule may be suitable for storage. But be careful, because it is from the vestibule that bikes are most often stolen.
Features of regular bike maintenance
Before starting a long bike ride, you should take it full service. Wipe the contour and frame with a damp cloth, then wipe dry. Wipe the chain either with a dry rag or with a cloth soaked in gasoline (be careful with this liquid). The chain must be free of sand and old oil, and must be dry and clean. After that, you can use oil - lithol, grease, Teflon grease.
After you put the chain in order, take care of the cables. Use engine oil. The brake and shifters also need to be lubricated regularly, and grit and old grease must be removed from them.
One of the rules for maintaining a bike is that you can lubricate everything that just spins - even the handlebars. Don't be afraid to go overboard with lube. Even if you dip your bike into a container of oil, it will not harm it.
Check the seat height using wrenches and hexagons, it is necessary to tighten each nut, screw and bolt. Don't forget to inspect the bike for rust. Especially in the lower part, where it forms most often. Corrosion is removed with sandpaper. After you have carried out the removal of plaque, use acetone and paint, and then varnish. Before starting a bike ride, you should make sure that the tire pressure is correct. You should not hear any extraneous sounds.
A lot of problems can arise during the maintenance of a bicycle. If you, for example, punctured a tire, disassemble the wheel, remove and inspect the tube. If the breakdown is serious, contact the repair shop. If only a small puncture - seal the camera yourself.
A brief video instruction for sticking the camera:
Our bike workshop in Moscow provides quality bicycle repair services. A team of professionals performs a thorough and high-quality repair of any level of complexity.
- We carry out seasonal maintenance of bicycles. Seasonal maintenance includes the following works: disassembly, cleaning and lubrication of all mechanisms (rear hub, front hub, carriage, steering column) assembly and adjustment. Replacement of consumables: high-speed and brake cables, correction of "eights".
- Forks are serviced: hydraulic and pneumatic (disassembly, cleaning, oil change, oil seals, dampers, etc.).
- Hydraulic brakes are being repaired. A full cycle of routine maintenance to restore their performance.
- We edit dropouts and forks.
- We make adjustment of gear shifting with electronic control.
- We repair bushings of any complexity, we replace bearings.
- We also perform all other repairs of bicycle equipment: (we disassemble all types of cassettes, cut threads in the bottom bracket assembly, assemble and re-spoke wheels of any complexity.)
- We make installation of any bicycle accessories.
* Bicycle repair is carried out in the presence of spare parts in stock.
** For warranty repairs and free Maintenance(applies to bicycles over 5000 rubles within 90 days from the date of purchase) bicycles are accepted on weekdays.
Prices on the site are indicated without discounts!Discount applies to renovations. ,
except for seasonal storage and installation of accessories!
Installing accessories
| 1 | Installation of quick-detachable plastic fenders (set) | 250r. |
| 2 | Installation of plastic wings (set) | 400r. |
| 3 | Installation of steel wings | 850r. |
| 4 | Bottle cage installation | 100 rub. |
| 5 | Mirror installation | 250r. |
| 6 | Lantern installation | 100 rub. |
| 7 | Installing the bike bag | 100 rub. |
| 8 | Installing the rear derailleur guard | 350r. |
| 9 | Installing a bike computer | 450r. |
| 10 | Installing a child seat | 700r. |
| 11 | Installing child extra wheels | 600r. |
| 12 | Installation of the trunk console (for the seatpost) | 350r. |
| 13 | Trunk installation | 500r. |
| 14 | Installation of a modular trunk | 700r. |
| 15 | Installation of peg (for 2 pcs.) | 350r. |
| 16 | Fitting or replacing a saddle | 350r. |
| 17 | Grip Replacement | 300r. |
| 18 | Installation of horns on the steering wheel | 350r. |
| 19 | Pump installation | 100 rub. |
| 20 | Installing the footrest | 300r. |
| 21 | Installing the basket | 600r. |
| 1 | Needle replacement (1 pc) | 50r. |
| 2 | Correction of eights on one wheel (axial runout) | 350r. |
| 3 | Eleps + figure eight correction | 850r. |
| 4 | Side impact fix | 950r. |
| 5 | Wheel assembly with spoke tension 26 | 950r. |
| 6 | Wheel assembly with spoke tension 20 | 1200r. |
| 7 | Wheel assembly when replacing: rims, bushings, spokes 26 | 950r. |
| 8 | Assembly of a wheel on hubs with a disc brake | 950r. |
| 9 | Wheel assembly when replacing: rims, hubs or spokes 20 | 1200r. |
| 10 | Selection of spokes for rim and sleeve | 100 rub. |
| 11 | Umbrella fix + figure eight | 600r. |
| 1 | Bust bushing front wheel+ lubricant | 600r. |
| 2 | Bust rear wheel hub + lubrication | 700r. |
| 3 | Hub adjustment (rear or front) | 300r. |
| 4 | Removal, installation of ratchet, cassettes | 350r. |
| 5 | Ratchet drum or cassette repair | 700r. |
| 6 | Removal, installation of a ratchet (freewheel) on BMX | 500r. |
| 1 | Cartridge Installation | 250r. |
| 2 | Carriage installation (bulk) | 500r. |
| 3 | Carriage adjustment | 250r. |
| 4 | Cartridge replacement | 700r. |
| 5 | Carriage bulkhead | 700r. |
| 6 | Bulk Carriage Override | 700r. |
| 7 | Carriage replacement | 700r. |
| 8 | Broach rods (2 pcs) | 100 rub. |
| 9 | Replacing connecting rods (without shift adjustment) | 350r. |
| 10 | Connecting rod installation (no adjustment) | from 350r. |
| 11 | Installing the "chain guide" on the carriage | from 950r. |
| 12 | Rockring installation | 500r. |
| 13 | Installing or replacing drive gears | 500r. |
| 14 | Replacing the cartridge (carriage) with the removal and installation of connecting rods | 1200r. |
| 15 | Editing the system of the first complexity | 500r. |
| 16 | Editing the system of the second complexity | 600r. |
| 17 | Editing the system of the third complexity | 700r. |
| 18 | Locksmith work (removal of connecting rods, removal of the carriage) | 950r. |
| 1 | Installing the pedals | 250r. |
| 2 | Pedal Replacement | 350r. |
| 3 | Pedal adjustment (1 pc) | 300r. |
| 4 | Sort out a regular pedal for a new lubricant (1 pc) | 500r. |
| 5 | To sort out the contact pedal for a new lubricant (1 pc) | 700r. |
| 1 | Surface cleaning chain + cassettes + rear derailleur rollers | 950r. |
| 2 | Chain replacement + shorten or lengthen | 350r. |
| 3 | Chain repair (depending on complexity) | 350r. |
| 4 | Chain lubrication | 50r. |
Steering column
| 1 | Replacing or installing a stem | 350r. |
| 2 | Steering column adjustment | 250r. |
| 3 | Steering column bulkhead | 850r. |
| 4 | Steering column replacement (with pressing out and pressing in cups) | 1200r. |
| 5 | Replacing the fork (without replacing the steering column) + cutting the stem | 950r. |
| 6 | Steering wheel replacement | 350r. |
| 8 | anchor pressing | 250r. |
| 9 | Pressing in 2 cups of the steering column | 600r. |
| 10 | Fork cut (according to the desired height) | 250r. |
| 11 | Fork and steering column replacement | 1200r. |
| 12 | Bleeding a hydraulic seatpost with a hydraulic line (Reverb) | 1200r. |
| 1 | Brake adjustment (1 pc) v-brake | 350r. |
| 2 | Disc brake adjustment. fur. (1 pc) or edit disc | 350r. |
| 3 | Replacement pads with adjustment (1 brake) v-brake | 600r. |
| 4 | Replacing brake levers (without adjustment) | 500r. |
| 5 | Installing the V-Brake (1 set) | 600r. |
| 6 | Disc brake installation. mechan. (1 set) with cable replacement | 950r. |
| 7 | Installing the V-brake kit (front + rear + adjustment, without handles) | 1200r. |
| 8 | Disc brake replacement. mechan. | 950r. |
| 9 | Installing a hydraulic disc brake (1 set) | 1450r. |
| 10 | Dressing disc/rotor | 350r. |
| 11 | Replacing Disc Brake Pads | 700r. |
| 12 | Removal / installation of the rotor | 350r. |
Switches
| 1 | Replacing the rear derailleur (editing the cock, cutting shirts, adjusting) | 950r. |
| 2 | Setpoint switch adjustment (full cycle) | 500r. |
| 3 | Replacing the front derailleur | 600r. |
| 4 | Installation of shifters (shift knobs) for 1 set. | 300r. |
| 5 | Front Derailleur Adjustment | 350r. |
| 6 | Replacing the rear derailleur rollers | 350r. |
| 7 | Replacing the Switch Cable or Jacket | 300r. |
| 8 | Rear derailleur repair or replacement | 250r. |
| 9 | Editing the front derailleur | 350r. |
| 10 | Disassembly/assembly of cable or jacket | 300r. |
Brakes "Magura", "Hayes"
| 1 | Installation of disc brakes (per pair) | 1900r. |
| 2 | Installation of rim brakes (per pair) | 1200r. |
| 3 | Hose replacement | 350r. |
| 4 | Replacement pads (1 brake) | 700r. |
| 5 | Bleeding (1 pc) (without oil cost) | 850r. |
| 6 | Flushing the caliper (1 pc) | 600r. |
| 7 | Adjustment of a brake (1 piece) disk | 350r. |
| 8 | Replacing caliper pistons or overhaul | 600r. |
| 9 | Handle Piston Replacement | 600r. |
| 10 | Bleed cap replacement | 100 rub. |
suspension forks
| 1 | Fork overhaul, oil change (J-TT, C, XC, J-1,2,3,4 Dart) | 2400r. |
| 2 | Fork rebuild, oil change (Pilot, Duke, Psylo, Tora, Recon, Reba, Revelation, Pike, SID, race) | 3600r. |
| 3 | Fork busting, oil change (SID team, World Cup, Boxxer, Domain, Lyrik, Totem, Argyle) | 3600r. |
| 4 | Spring-loaded, elastomer forks | 1800r. |
Additionally
| 1 | Replacement of oil seals | 600r. |
| 2 | Replacing guide rings | 1200r. |
| 3 | Air spring replacement | 950r. |
| 4 | Spring replacement | 500r. |
| 5 | Replacement service kit | 350r. |
| 6 | motion control replacement | 350r. |
| 7 | Changing pants | 700r. |
| 8 | Damper replacement | 950r. |
| 9 | Oil for forks 1 gr. | 1r. |
| 1 | Bicycle overhaul | negotiable |
| 2 | Transfer of equipment from frame to frame | negotiable |
| 3 | Bicycle diagnostics without repair | 300r. |
| 4 | Seat post cutting | 250r. |
| 5 | cut horns | 250r. |
| 6 | Cut the handlebar to the desired length | 250r. |
| 7 | Threading in the frame (under carriage 1.37 36/24) | 950r. |
| 8 | Fork threading 1.1 1/8.1 ¼ | 600r. |
| 9 | Air rear shock bulkhead + oil | 2400r. |
| 10 | Bust rear suspension (without removal of feathers) | 1200r. |
| 11 | Bust rear suspension (with removal of feathers) | 1800r. |
When self-maintenance of your bike, there is a chance of "screwing up" and doing something wrong. Let's look at a few points where mistakes can be made when servicing a bicycle. How to properly maintain a bike?
Do not overtighten the bolts. Now, in an era of lightweight carbon fiber components and tiny bolts with small wrench heads, you need to have sensitivity when tightening them. It is better to purchase good adjustable wrenches with suitable torx sockets and hex keys.
Lubricate the threads, the base of the bolt and both sides of the washer first. Screw designs with two bolts a little, holding the tool alternately with your fingers. Use a tool with short handles and do not lengthen them. You don't have to push hard, or you're bound to break something.
Steering column
Find out in advance how to properly regulate steering column and then parse. Never tighten the top cap without loosening the stem bolts, or you will break the cap, spider nut, or wedge that is inside the fork stem. In extreme cases, the wedge may come out of the steering column and no further adjustment will be possible. When this happens, put back the wedge 2 cm below.
Make sure the stem protrudes from the top and the gasket washer protrudes from the edge of the stem by approximately 5mm. Place the cover on top and tighten the adjusting bolt. There should be no play in the bearings, and rotation at the same time free.
spokes
Straightening the figure eight on the wheel by tightening the spokes alone will not work. Some need to be pulled, others need to be loosened. It is impossible to align the wheel without fully understanding the whole process and sequential actions. Of course, the only way to learn this is to try it yourself, but practice should be done only after mastering a sufficient amount of theory.
There is a rule: with one turn of the spoke nipple on the side where there is no chain, twice the effect is achieved in the transverse direction than with one turn of the spoke nipple on the side of the chain. To avoid over-tightening the spokes when making a lateral adjustment, tighten the spokes a little on one side while loosening them a little on the other. If you licked the edges on the nipple, then this means that you overtightened the knitting needle.
Rims
Control rim wear limits when using rim brakes. Miss it - the consequences can be sad. Many rims have a wear indicator in the form of a shallow groove in the braking surface or small holes in key and marked areas. Check these markers regularly. When they become invisible, the rim must be replaced. If there is no wear indicator, then measure the wall thickness with a caliper. If they are less than 1 mm, then the rim must be replaced.
Safety
Work slowly to avoid injury while working. When tightening or loosening a tight thread, be aware of where your hands are pointing or what they might hit if the tool breaks. When working with crank bolts or pedals, install the chain on a large star - it will cover the teeth and prevent injury on impact. Wear protective gloves and never rush. Try to stand in such a way that you always pull towards you with your hands, and not push with the weight of your whole body.
seatpost
Do not forget about the seatpost for a long time (6-12 months). With a lingering seatpost you can not change the height of the seat, and sticking can be eliminated only with the help of expensive repairs. Even if the pin is lubricated, over time the lubricant oxidizes and breaks down. Not only metal pins can stick to the frame, but also carbon ones, even if both the pin and the frame are carbon. The pins should be lubricated regularly, having previously cleaned them of dust, sand and dirt.
Pedals
It is undesirable to wind the pedals on dry threads and tighten them too tight. If you install the pedals without lubrication, it means that you will have difficulties in the future when removing them. Pedaling most likely ends with a visit to the bike shop, where you will pay decent money for the work to remove it. In addition, without lubrication, thread corrosion occurs, and the pedal sticks to the connecting rod at the threaded connection, and when unscrewed, the thread will crumble. When installing the pedals, it is necessary to use grease and a protective cap, if necessary, tighten it strongly, but do not overtighten, it is better to use a torque wrench.
Tire pressure
Check tire pressure regularly. Driving with flat tires will weaken your confidence and reduce your speed. Check tires before driving, thin wall tubes lose 5 to 20 psi per day. Check the pressure either by pressing hard with your finger on the tire, or by clicking on it with your finger - it should make a dull drum sound, in addition to being quite firm to the touch with the correct pressure.
Use a pressure gauge to inflate your tires to the correct pressure before you learn how to properly feel it. It should be noted that the tire pressure should be slightly less than normal.
eccentrics
Do not ride with loose eccentrics. Before riding, check the quick-release clamps on the wheels - this can prevent injury. The eccentric clamp is often treated like a regular nut and is simply screwed on by the handle. This can only be done with clamps from certain manufacturers. With all others, you need to clamp the handle already on the twisted axis. The eccentric handle must be firmly fixed in the closed position.
Circuit status
Take chain condition seriously. Do not ride when the chain is not properly installed. Many bike mechanics during installation will damage the chain and leave it to work, in the hope that everything will be fine. However, considering how much stress the chain is subjected to, any defect can lead to a catastrophic situation. Bad links must either be replaced or a connecting universal link must be used. Don't forget about chain wear. It can lead to uneven and premature wear of sprockets. Measure chain wear regularly or simply change it every 2,500 km or so.
More articles on this topic:
Bleeding disc hydraulic brakes is a serious and responsible job, so you need to approach it prepared ...
Squeaking is when parts of a bicycle rub against each other, it is necessary to determine the place of the squeak, sort out and lubricate the components. Practice shows that the most difficult thing is to determine the source of the sound ...
A bicycle is a rather complex mechanism, consisting of many nodes that require systematic care and maintenance ...
Let’s take a look at the preventive lubrication scheme for a bike – bike parts that work in the open state, and therefore get dirty quickly and require more frequent cleaning and lubrication…
It depends on the riding style, operating conditions and personal attitude of the biker to his bike, the wear of the main components can be different. But if you do not take into account the extremes, then ...