Rubric -

When operating the MTZ-80/82 tractor with wide-cut implements, install forks 5 and 23 (see Fig. "") on the slot. This will provide better adaptability of the implement organs to the soil relief along the width of the grip.

The design of the right brace 17 provides for its length adjustment using the handle 21.

To decrease the length of the brace, turn the handle counterclockwise, to increase it - clockwise.

Do not adjust the left brace when working with attachments, its length must be constant and equal to 515 mm. To level the plow in the transverse plane, adjust the right brace.

The alignment of the depth of travel of the front and rear working bodies of the mounted implement is ensured by adjusting the length of the central rod 24. Adjust the length of the rod 24 by rotating the pipe using the handle 25.

Make sure that the brace, limiter chains, and center link locknuts are securely tightened: loosening the locknuts can result in misalignment and thread breakage.

Shorten the central link 24 in order to improve the cross-country ability of the machine during long-distance travel of the tractor with the implement.

Adjusting bolts 8 are screwed into the brackets 6, which provide tension to the chains when the implement is raised to the transport position to reduce its swaying in the transverse plane.

Adjust bolts 8 in the following order:

1. attach the implement to the hinges of the longitudinal and central rods. Screw the adjusting bolts 8 into the brackets to the full.
2. raise the implement so that its working parts do not touch the ground.
3. adjust the length of the limiter chains by turning the turnbuckles so that the trailing link joints can swing freely in accordance with the implement manual. For mounted plows, the freedom of swing in the horizontal plane should be 125 mm. on each side of the middle position.
4. adjust the length of the right brace to the desired working depth (when working with plows).
5. raise the implement to the transport position by unscrewing bolts 8 from the brackets, tension the chains so that they sag slightly, ensuring that the implement swings no more than 20 mm. round trip.
6. secure securely with locknuts. Accompany each change in the length of the right brace by adjusting the right bracket bolt to ensure self-locking of the limit chains.

When inter-row cultivation, sowing, as well as when working using the longitudinal links of the mounted device, block completely from lateral movements in order to avoid damage to plants or swaying of the implement. Blocking is carried out by shortening the length of the chains as much as possible within the existing adjustment; in this case, screw the adjusting bolts into the bracket until it stops.

Failure to follow this order may result in interruption of the limiter circuits or other damage.

To block the attachment in transport position do the following (see fig. " "):

• 1 - open the rear window of the tractor.
• 2 - raise the hitch to its highest position by setting the distributor handle to the "lift" position.

The stop 10 of the hydromechanical valve of the hydraulic cylinder must be in the rearmost position on the rod of the hydraulic cylinder.

• 3 - lower the handle 13 to the lower position.
• 4 - put the distributor handle in the "floating" position. Under the action of the mounted implement, the rotary arm will turn and the tooth 12 should come into contact with the grip 1.

To unlock the hitch, do the following:

1. raise the hitch to its highest position by setting the distributor handle to the "lift" position.
2. raise the handle 13 to the top position.

A jump rope can be considered a very affordable and inherently simple sports simulator used by both advanced athletes and ordinary people, even those who have just decided to take care of their health and appearance. For all its simplicity, the jump rope is a fairly complete cardio simulator that helps to part with unnecessary kilograms, keep muscles in good shape, improve the condition of the heart and blood vessels, and even cheer yourself up! In addition, it does not take up space in the house, and moreover, it fits in your pocket! What do you need to know in order to choose the right thing for such a wonderful thing and how not to make a mistake when choosing the length of the rope? Just a few factors. One of them, the most important - how long the rope should be.

Just about how to choose a rope, our article tells. For this, some simple knowledge will come in handy. You definitely need to know how to choose a rope for your height, as well as the material of its manufacture and additional functions, if they are desired.

Rope training is also called "skipping" - ("skipp" - in English "jump").

So, the very first and important point of our choice will be the length of the rope by height. After all, it is not pleasant if, during jumps, the cable strikes the legs, and this will happen if its length turns out to be short. bad and redundant long jump rope, since then its cable will be dragged along the floor, getting confused and slowing down the training process. It is desirable to practice with a rope comfortably, with benefit and without all sorts of unpleasant surprises.

How to choose a jump rope for height?

Method 1

Going up to the showcase with jump ropes in the store, take the one you like in your hands, its cord should go down to the floor. Step on the middle with your feet. Now you need to spread the handles of the rope a little to the sides, leading to your armpits. If at the same time the ends of the arms just reach the armpits- the product corresponds to the growth, "must be taken."

Method 2

There is another way telling how to choose the length of the rope. To do this, you need to fold it in half, take it with your hand immediately by the two handles. Next - we stretch the arm with the rope in front of us at an angle of ninety degrees in relation to the body. FROM the rope should touch the floor with the lower end of the cord without lying down on it and not hanging in the air.

Method 3

But how to choose a rope by height if there is no way to try it on, as, for example, when making a purchase through an online store? Created for this case table of the ratio of human height with the length of the selected product:

• With a person's height of 150 cm, we choose a rope about 2 meters long;
• If the height is from 151 to 167 cm - the length of the product is about 2.5 meters;
• From 168 to 175 cm - 2.8 meters;
• From 176 cm to 183 cm we buy a three-meter rope;
• For people taller than 183 cm, a rope length of 3.5 to 3.8 meters is required.

It is better to buy a skipping rope in sports shop where an experienced and competent consultant will assist in the selection. If the purchase is made through an online store, find and read as many reviews as possible about the selected rope.

These are the basic rules on how to choose the right rope for height. Although, even following all the above tips, a person who buys a rope for the first time can make a small mistake, which, of course, is undesirable. After all, even a few extra or, conversely, missing centimeters of cord length can significantly affect the quality of training. The ability to accurately determine how to choose the right rope for height comes by experience, but in order to immediately do without mistakes, there are jump ropes with adjustable cable length. In addition, with the possibility of adjusting the length, one rope can be used by more than one person, but by all family members!

A jump rope with adjustable length is the perfect purchase for a sports family!

How to adjust the length of the rope?

When buying an adjustable rope in a store, you can ask a consultant how to adjust the rope for height. Such jump ropes have clamps located near the handles. After pulling the cord to the required length, you should clamp it. As a rule, a length regulator is provided for high-speed ropes that also have a hinged device on the handle to speed up the rotation of the cord. Now we will describe the choice of a rope according to its functional purpose.

• For regular workouts perfect fit the most common inexpensive jump rope a.
• For more intense workouts need to purchase speed rope, characterized in that it has a hinged mount on the handle, which allows you to increase the number of rotations. The purchase of such a projectile is attractive from a financial point of view, since it can be used as a beginner at the beginning of his sports way and those wishing to further raise the level sports loads. This jump rope is ideal not only for endurance and speed training, but also for weight loss.
• For those who want to lose weight would be a great tool electronic skipping rope, which allows you to constantly monitor the process of weight loss. It will make training both useful and interesting. This jump rope counts calories burned during a workout. A sensor is mounted in its handle of the rope, which records jumps and energy costs. We enter our weight, and after training we look at the monitor of the device. It shows how many jumps were made and calories burned. In addition to a calorie counter and energy consumption, such a smart rope can have a timer.

How to choose a jump rope according to the material of the cord?

For the effectiveness of training, it is also important to know how to choose the right rope based on the material of the cord and handles.

The cord can be:

• Nylon- We recommend it for beginners and children. He is very soft, his blows to the body are not painful. But a nylon cord will not provide intense training, jumping with it will be slow.
• Rope- also light and non-traumatic, not durable and will not be able to provide high speed.
• rubber or plastic Both of these options are suitable for beginners. They are elastic, durable, do not get tangled. The plastic cord is more rigid, it cuts the air better than the rubber one, which contributes to a more intense pace of training. Rubber cords are not flexible enough and can be difficult to straighten after being rolled up for a long time.
• steel, with or without length adjustment. Used for speed ropes. The cable is finished with a PVC or silicone braid on top, which protects it from moisture and other influences, making it possible classes on the street. Not suitable for difficult jumps with twisting of the line - it can break. Traumatic.
• Leather. Differs in durability, does not tangle, rotates - great option for professionals. Among the shortcomings - it cannot have length adjustment and is expensive.
• beaded, consisting of plastic multi-colored beads. Such ropes are bought for children, so that playing sports arouses their interest and brings joy. This jump rope is quite light and does not get tangled.

Features: too light, like heavy ropes - not for speed jumps! This applies to nylon, leather jump ropes and with a rope cord - they are very light, but rubber ones will be too heavy. The fastest - jump ropes with a metal cable

How to choose the right rope for the material of the handles?

Handles - it would seem that such a small detail of the rope, but it is quite important what they are made of.

• Neoprene- a recognized leader in all respects. It perfectly removes moisture, as a result of which the handle remains dry and the rope does not slip out of your hands during even very long workouts;
• Wood- also a good material, non-slip, but not as practical as neoprene;
• Plastic- light, pleasant and good material, but loses in comparison with neoprene because the accumulated moisture from sweaty palms makes such handles slippery;
• Metal- you can call it a male athletic option, since it provides for a weighting of the structure, which gives an additional load on the shoulders and arms;
• Rubber- durable, inexpensive, wear-resistant, but heavy material. For the beginning of a sports path, when short workouts are planned, the choice of such handles is quite reasonable, but for long workouts it is not worth considering.

Instruction

Select the Options tab in the window. Here are the elements for setting display options. Using the "Screen Resolution" slider and moving it with the mouse, change the . Set the points you need, while referring to the numerical values ​​​​displayed below the slider.

Set quality. To do this, in the same window, in the corresponding drop-down list, select the desired value. After setting all the parameters, review the changes by clicking the "Apply" button.

After the display blinks for a short time, its resolution will change according to the set data. In this case, the "Monitor Settings" window will appear on the screen, informing you of the change in size. If you are completely satisfied with the visualization with the new resolution, click the "Yes" button in this window - confirming that the parameters have been saved. Otherwise, the "No" button. Also, by default, changes will be canceled by the system automatically after 15 seconds.

note

The optimal resolution of the monitor should be selected taking into account its technological features. Some older models may not support resolution high level.

Sometimes, during the process of reinstalling the operating system, or after an incorrect shutdown of an application, such as a video game, the screen settings are reset. As a result, the displayable area of ​​the screen on the monitor becomes smaller, the resolution is set to the standard 800 x 600 dpi, and black bars appear on the sides of the screen. In such a situation, you need to restore the screen values ​​to the original settings.

To stretch the screen correctly, you need to right-click on an empty space. In the menu that appears, select the "Properties" command. The Display Properties dialog box opens. Select the "Settings" tab. In the window that opens, an image will appear on the computer monitor and adjustment scales for selecting the screen resolution and color quality. If the resolution scale is set to 800 x 600 dpi, then use the slider to increase the value to the maximum size, for example, 1280 x 1024.

Sometimes the slider fails. This suggests that the computer may be in safe mode, for example, when forced to restart, or when absent (the slang term is “flew”). In such a situation, in order to stretch the screen correctly, you will need a driver from the disk that came with the video card, or download it from the Internet from the equipment manufacturer's website. But first you need to make sure that this is the problem.

To do this, on the "My Computer" icon, right-click to activate the menu and select "Properties". Then in the window that opens, select the "Hardware" tab and "Device Manager". First, select "Display Adapters" from the list and right-click to activate the "Properties" command. In the window that opens, select the "Driver" tab. We carefully look at the information about the date of the driver update and the current version. If it says that the driver is missing or not found, you will have to reinstall it. This is a hardware failure that can only be fixed by reinstalling the video card driver.

If the video card driver is installed and the General tab indicates that the device is working properly, then you need to check the monitor driver. We execute a sequence of commands - "My Computer" - "Properties" - "Hardware" - "Device Manager". In the list, select "Monitors" and right-click to activate the "Properties" command. In the window that opens, select the "Driver" tab. If not, you will also need to reinstall it.

The screen resolution of the monitor is responsible for the clarity of the image and text, as well as for the correct positioning of the image on the screen. The higher the resolution, the sharper the objects appear on the screen, and at the same time, the smaller they become.

Instruction

The smallest resolution on modern computers is 640x480. The first number indicates the amount along , the second - vertically. So, at 1280x960, one point at this resolution will occupy 4 pixels, thus the image will be blurry, bulky, photos and labels will be angular.
The optimal resolution is 1280 horizontal pixels for monitors with a diagonal of 14-15 inches. Monitors from 17 inches use a higher resolution, such as 1600, 1920 or more horizontal dots.

To change the resolution in Windows XP, right-click on the desktop, select "Properties" from the context menu that appears. In the window that opens, go to the "Settings" tab and move the horizontal slider in the "Screen Resolution" section to the resolution you need. On the right, here, you can change the color quality. The desired parameter is 32 bits. After that, click "Apply" and see the result. If the quality of the image on the screen does not satisfy you, continue to experiment with the slider.

If you have a Windows Vista or Windows 7 computer, right-click on the desktop and select Screen Resolution. In the window that appears, select item number 2, click on the drop-down menu and move the vertical slider to the desired resolution, then click "Apply" and pay attention to the result. Also here you can change the screen orientation from landscape to portrait or flip the image on the monitor.

Related videos

note

In addition to screen resolution, an important option for vision is the screen frequency. The higher the flicker frequency, the less eye strain.

Sources:

• how to change resolution on tv

Resolution is a monitor setting that determines how information is displayed, measured vertically and horizontally in pixels. At a lower resolution, such as 800x600, there are fewer elements on the screen, but they are more large size. At higher resolutions, such as 1280x800, more smaller elements fit on the monitor. It is best to use a computer with a maximum screen resolution, which is different for each monitor.

Instruction

Use the "Resolution" slider to set what you need. Click OK. The screen will turn black for a second. The operating system will ask you to confirm the new settings within 15 seconds, if you do not, the computer will return the old settings automatically.

Related videos

note

Changing the screen resolution affects all user accounts on that computer.

Useful advice

For some older games and programs, a screen resolution of 640x480 pixels is required. You can temporarily enable this mode. To do this, right-click on the shortcut for this program and select "Properties". Go to the "Compatibility" tab and check the box "Screen resolution 640x480". Click OK. When you close the application, the screen resolution will return to normal automatically.

Now that monitors have become cheaper and more affordable, many users have begun to put two monitors on their computer desk. The advantages of such an approach are obvious. You can work on one monitor and watch a movie on the other at the same time. You can also connect a TV, a second keyboard, and a mouse to your computer as a second monitor. Then several users can work on one system unit.

Instruction

With the advent of the new operating system Windows 7, the situation was resolved. But Microsoft has made this solution so non-obvious that many users, especially unprepared ones, will not immediately figure it out. There are two ways to solve this problem.

When you highlight a specific window (naturally, when it is in the active state), pressing the keyboard shortcut "Win + Shift + Left / Right Arrow" moves the selected window to the right or left.

Related videos

Useful advice

The use of a second monitor in the Windows XP operating system created an unsolvable problem. If the second monitor or TV was turned off, then open windows on the second monitor remain. And you have to drag these windows back and forth manually. Before dragging, you need to turn on the second monitor. There were, of course, some more successful, some less successful ways, but they differed only in additional "body movements".

Sooner or later, any user faces the question of changing the screen resolution. This can happen after exiting the game incorrectly or due to a desire to see what is happening on the screen more clearly. Before understanding this process, we first define what it is and what it is responsible for.

You will need

• A computer

Instruction

Resolution is responsible for the clarity of the display of objects, i.e. labels, text, pictures, windows, etc. It is in pixels and depends on the monitor settings. If the user wants to be comfortable for his vision, then he simply must be able to change the screen resolution.

In order to change the resolution, right-click once on an empty space on the desktop and go to "Properties". Of the five tabs that open: "Themes", "Desktop", "Screen Saver", "Design", "Settings", select the last one and use the slider to select the most convenient for your work and suitable value.

As you can see, changing the resolution is not so difficult, but you will ensure your comfort while using your computer. In general, we can say that changing the screen resolution is the same in almost every operating system.

Sources:

• as you can see it has changed

The presence of an expensive video card and a good monitor is still not a sufficient condition for comfortable work at a computer, since their correct settings are necessary. An improperly configured video system, even the most modern and expensive, will only bring you disappointment and fatigue to your eyes.

You will need

• Computer running the Windows operating system (XP, Windows 7), basic computer skills

Instruction

By moving the “Screen Resolution” setting slider, set the resolution that will allow you to work without stress. The value of this parameter is very individual, depending on the preferences of the user. If the image is too large at the selected resolution, then go to the "General" tab and increase the "Scale Factor" value.

Open the Monitor Connection Module Properties window by clicking the Advanced button. On the "Monitor" tab, set the screen refresh rate. The higher this value, the less your eyes will get tired from monitor flicker. Click the "Apply" button for all changes to take effect.

If your operating system is Windows 7, use the dccw.exe application. Launch it from the "Control Panel" "Display" applet by clicking on the "Color Calibration" button. The setup assistant window will open, where, following the suggested steps, you can fine-tune your computer's video system.

Related videos

Sources:

• How to change monitor screen resolution in 2018

In Moscow, in order to get a job, foreign citizens must have registration and a work visa to Russia. In Russia, for foreigners, a work visa is issued at the place of residence. If a citizen changes his place of residence, he should re-register and obtain a work permit. For registration, a foreigner must provide a personal passport and migration card. The registration is usually valid for one year. After the expiration of the period, foreign citizens are required to renew their registration.

You will need

• Personal passport, migration card.

Instruction

Obtain permission for (visa) from the Office of the Federal Migration Agency, if you are a citizen of the CIS countries.
If you are a citizen of countries such as Turkmenistan and Georgia, then first get the consent of the employment center. If you are a citizen of Belarus, then do not worry about obtaining a certificate of permission to work in Russia, you do not need it.

If you already have a work permit (for at least 90 days), then within a month, submit medical certificate in the FMS, which confirms the absence of HIV and infectious diseases, drug addiction, alcoholism. If the certificate is not submitted within the specified time, the work permit will be invalidated.

Related videos

note

In Russia, it is against the law to work without documents (registration at the place of residence and a work visa). It is important to remember that failure to comply with this law entails heavy administrative fines and expulsion from the country. At all stages of employment, it is necessary to comply with the deadlines for submitting and processing documents.

Useful advice

Today, for foreign citizens, obtaining a work permit in Russia is mandatory. It is important to take into account the peculiarities of obtaining a work visa for citizens of different countries. In Moscow, on employment issues, you must contact the local Federal Migration Service.

Sources:

• On the acceptance of documents for obtaining a work permit. in 2018

Some users are unhappy with the image transmitted by their monitor. Everyone solves this problem in their own way. You can purchase a different monitor, customize an existing one, or connect another device instead of a monitor.

You will need

• - video signal transmission cable.

Instruction

First, try expanding your monitor screen by increasing its resolution. Usually this method allows you to capture more usable screen area. In Windows Seven, open the Control Panel and select Appearance and Personalization. Now open the "Screen" menu and go to the item "Screen resolution settings" located in the left column.

In the "Screen Resolution" menu, set a larger value. At this method there are several disadvantages: deterioration in the quality of the image transmitted from the monitor, and a decrease in the screen refresh rate. If you are not satisfied with the result, then connect an additional monitor. As its analogue, you can use a liquid crystal or plasma TV.

Connect another monitor or TV to the second connector of your video card. This process can be carried out even when the system unit is turned on. To connect a TV, it is recommended to use connectors that transmit a digital signal. Now repeat the procedure for entering the monitor settings menu.

Click the "Find" button and wait while the system detects an additional device. Now select the graphic image of the second monitor and activate the "Make this screen as the main screen" function. This will allow you to use a TV (higher quality monitor) instead of a standard device.

To greatly increase the working area, select the "Expand this screen" option. On one of the monitors (the one that is secondary), all shortcuts will disappear and only the desktop picture will be displayed.

To launch an application on the second screen, simply drag it with the cursor outside the first monitor (left or right). Note that it is recommended to set both screens to the same resolution. Otherwise, not the entire working area will be occupied on one of the monitors.

Related videos

Resolution is a term applied to images in digital form. The "picture" of the desktop and all the icons on it are also a digital image. What screen resolution is selected will depend on the appearance of the desktop and all files being launched (large or small icons of folders and files, their normal or stretched appearance, the appearance of file captions, and so on). You can restore the previous or set a new screen resolution in just a few clicks.

Instruction

To adjust the screen resolution, open the Control Panel via the Start menu. When the Control Panel is displayed by Category, select Appearance and Themes. In the window that opens, either select the "Change screen resolution" task, or click on the "Screen" icon. If the control panel has a classic look, immediately select the "Screen" icon by clicking on it with the left mouse button. The Display Properties window opens. To switch from displaying the control panel by category to the classic view and vice versa, click the appropriate label command on the left side of the control panel dialog box.

There is a big trouble in the house - the limb of one of the family members is damaged, and the doctor strongly recommended crutches.

Crutches can be bought The height of the patient must fall within the range of the passport size of the crutches.) or ask for already used but in good condition.

Let's review the new acquisition.

To begin with, let's check the crutch for strength (each crutch in the pharmacy has its own maximum calculated weight), then check the upper axillary bar for smoothness (or for depreciation usefulness if it is covered with elastic materials). Check the presence and quality of all bolts or studs that adjust the length of the crutch. And finally, let's check the rubber tip of the crutch - is it worn, does it hold well, is it the same wear if the crutch is not new.

And only now will we begin to solve the problem of fitting these crutches to a given person.

I emphasize once again: the problem of “how to properly adjust the crutches” cannot be solved “by eye”. You will have to lift the future user and with the help of a wall, a chair or one or two assistants, straighten him to his full height.

First of all, we solve the problem of the height of the crutches. The main thing in this matter (how to adjust the crutches for height) is not to make the main mistake: not to make them too high. Many people think that correct setting crutches for growth requires a hard stop of the crutch in the armpit. This is absolutely false!

With a full vertical scan of the patient, the upper bar of the crutch should be 4-5 cm below the armpit!

Now adjust the height of the hand grips - They should be at the level of the thigh. In this case, the arm should be slightly bent at the elbow joint.

Ask the patient if they are comfortable with the height of the hand grips in the vertical position.

How to set up crutches

Thus, the correct adjustment of crutches consists of two operations:

1) adjust the total length of the crutch with the screws below

2) adjust the height of the hand grips.

I want to cool the ardor of the impatient - the first time you will not achieve absolute convenience.

The problem of how to properly adjust crutches will have to be solved throughout the entire time of use.

A person will change shoes, begin to grow stronger and naturally straighten up, begin to walk up and down stairs.

Anyone who has ever bought a new watch with a metal strap must have encountered the problem of the length of the strap. Initially, the strap on the watch is designed for the largest possible wrist, but this big size does not suit most. To make the watch sit comfortably on your hand and not move out, you have to shorten the strap. Many in this case use the services of a watchmaker. In principle, we also do not mind that everyone should mind their own business. However, shortening and adjusting the length of a metal strap on a watch is not such a difficult task. To do this, it is enough to have a set of tools, skillful hands and 15 minutes of free time. If you doubt this, then perhaps we will dispel your doubts if you read our article. It is in it that we will talk about how to shorten (adjust) the metal watch strap to the length you need.

Which watch straps cannot be adjusted (shortened)

Despite the fact that we all have different ergonomics, not all watch straps are adjustable. This is due to everything not with the fact that manufacturers wanted to complicate our lives, but with the fact that they do not need it.
Let's say the leather straps that our grandparents used to wear, which close like a belt on a belt. These straps are adjustable every time we put them on our hand. In fact, they are fixed according to the size of the hand, thus they do not need a separate adjustment.
There is another type of non-adjustable watch straps. These stretchable straps. Each of the links in the bracelet of such a strap contains a spring. As a result, the whole bracelet springs. When the bracelet is worn on the hand, it stretches, and then it wraps around the hand. It does not need adjustment, and it is not possible to make it.

Such watch straps are extremely rare and have become a kind of rudiment, an anachronism of our time. However, they also have fans who consider them stylish, comfortable and pragmatic.

Which metal straps can be shortened in length and with which tools

The title of this paragraph is somewhat abstracted from reality. Most watch companies take the ability to shorten, adjust the length of a metal strap as a matter of course. So, it is more difficult to find watch straps that are not adjustable than adjustable ones. Simply put, almost all metal straps on branded watches such as Orient, Casio, Citizen, etc. can be shortened or adjusted. It is also important to note that there are two fundamentally different kind straps. Those that are assembled on rods and those that are assembled on plates. In our review, we will talk about these two most popular options.
To adjust and change the length of the metal watch strap, we need tweezers and a thin awl. In our case, a simple Chinese tool kit was used for these procedures.

Now straight to the point...

The process of adjusting the metal strap on the watch (Orient, Casio, Citizen)

Adjustment differs, first of all, in a slight range of change in the diameter of the strap on the watch. If I can say, then it is performed as a finishing operation. In the case when it is necessary to adjust the diameter by 0.5 - 2 cm.
Thus, most watches provide for adjustment by moving the retaining rod in the holes of the closing lock on the watch strap bracelet.
Initially, the rod is pressed out of the lock with a thin tool.

Then, it is placed in the holes that are closer to the already installed rod on the other side of the strap lock.
As a rule, the rod that is installed in a uniform row of holes gets it. The second rod is either removed from them, or slightly displaced, it is not necessary to get it.
The rod must be taken out (placed) carefully, as it can jump out, due to the fact that it is spring-loaded in the lock. As a result, it can not only fly away to where you will not find it, but also crumble into its constituent parts.

The process of shortening (removing a link) from a metal watch strap (Orient, Casio, Citizen)

The process of shortening the strap involves removing one or more links from metal bracelet hours. In this case, initially, as well as during adjustment, one of the rods on the lock will be removed. As a result, the strap "opens", now you can work with it.

Next, you need to pay attention to those links that can be dismantled. You can only dismantle those sections of the strap where the arrow is. Where there is no arrow, these links are non-separable among themselves. So, in our case, we will give two possible options for connecting the strap, which we have already mentioned. In the first case, the belt is connected with the help of rods, in the second case, with the help of plates. How do rods...

So are the plates...

They are pulled out in the direction of the arrows (seen in the photo) and only from those links where these arrows are, as we have already talked about. The rods diverge at their end. Therefore, when they are in the strap, they may seem like a small screw, but they are not.

As for the straps on the stem, things were not always smooth with them. Even having a seemingly suitable tool, the rod in the strap sometimes went inside, while not always being pulled out from the opposite side. As a result, the cone of the tool reached the very bracelet, and could damage it. (see picture). Although these damages are not very noticeable, but if the watch is expensive, it will not be very pleasant. The best option was to use a paper clip. A small rod, about 5-7 mm, was bitten off from it with wire cutters, and inserted into the hole. The rigidity of such a home-made tool was quite enough to knock out the strap rod to the end, without damaging the ends of the strap. The blows on the protruding segment of the paper clip were made with a plastic screwdriver handle, that is, not very hard and not with a metal object.

Sliding lock watch straps

Another option for adjusting the strap, or rather not even the watch strap itself, but changing the diameter under the arm is carried out due to the “sliding” lock. This lock can be moved along one of the watch straps, thereby adjusting the diameter of the wrist.

This is the easiest option, when adjustment does not require a special tool, except for a flat-blade screwdriver. The fixing tab of the lock on the strap is retracted to the side and then, after adjustment, goes down again.

This is by far the easiest option in terms of adjusting the length of the strap that you will encounter on a watch.
At the same time, note that using this technology, manufacturers have combined a stylish leather strap with the convenience of using it like a metal one. When the belt fastens in one motion, without the need to "catch" the holes and waste time and nerves.

As a result, having released one of the links on the watch strap, we simply assemble it back. Due to the operations performed to dismantle the link, the strap becomes shorter by this link. If removing one link from the strap did not help, then in the same way you can remove other links where there is an arrow. If you need to remove several links, try to remove links on symmetrical sections of the strap, on one side of the lock and on the other.
As you understand and see, the procedure is not particularly troublesome, but rather requires attention and patience. Now you can not only adjust, but also change the length of the metal strap on the watch.

Video on how to shorten a watch strap